rtical pole has an out inside diameter of 250 mm. The pole is subjected to a waries uniformly from 800 N/m at the base to 1200 N/

Q: Please recalculate and maksure everything above is correct. thanks

A: Steps to solve this question:Assumptions and sign conventions of forces and reactions.Find the…

Q: What are the two main types of Structural Loads? Describe each briefly.

A: To find :  Two main types of structural loads .

Q: What is the difference between working joints and non-working joints?

A: Sealants are defined as material that is used to seal or block the route of the liquid and make it…

Q: What is the Regional Differences in Capillary Pressure?

A: Solution: Capillary pressure is basically determined by centrifuge experiments which generally…

Q: C D E B b A H J K a a a a + a a P1 P2 PA P3 Determine the force in members FE, LE, and KL of the…

A:

Q: Kindly please get that acting force on member BF

A:

Q: What makes a load a live load?

A: The loads are called the live loads in the following cases i.e when the loads are: Temporary loads :…

Q: How does bending stress impact engineering design?

A: Bending stress can be defined as the normal stress that is generated when any structural member is…

Q: 1. Determine the horizontal and vertical components of the reaction at A and C. 35 kN/m 8 kN/m 2 m…

A:

Q: What is the vertical  reaction at hinge support? What is the horizontal reaction at hinge support?

A: Length of the span AB -  LAB = 242 + 102⇒LAB = 26m   Taking the span Ab as the horizontal for the…

Q: What's the advantage of Composite structures?

A:

Q: Please answer completely. Box the final answers. Use the graphical method to construct the…

A:

Q: What is thixotropy?

A: Thixotropy can be defined as it is time-dependent shear thinning quality. In this, a certain fluid…

Q: Name two differences between flexural and local buckling.

A: In structural designing, buckling is the abrupt change in shape (twisting) of an auxiliary part…

Q: Determine the tension T in the belt needed to overcome the tension of 200 lb created on the other…

A: Given :

Q: Problem 4 The shown bent tube is connected to a guide at A and rests on a roller support at B. It is…

A:

Q: Determine the load of W required to cause collapse of the frame if the plastic moment of all members…

A: Plastic Moment, Mp = 200kNmTo Find: Magnitude of Load, W

Q: how apply wind load on a structure....

A: Any structure is more than 15m in height then wind load is considered essentially. Wind exerts…

Q: What are the types of loads on structures?

A: Structure is an assemblage of load carrying members such as footing , column, beam, slab and wall.

Q: Define the structural capacity of an element in OpenSees?

A: The Open System for Earthquake Engineering Simulation (OpenSees) is one of the many projects under…

Q: what is force in FG

A: Given data in question  Force 60 kips Span 16 m Height 15 m To find out  Member force in FG

Q: does

A:

Q: What are the three types of shear tests? Name and describe.

A: The three types of shear tests are-  1. Direct shear test  2. Unconfined compression shear test 3.…

Q: 帅 E 誰 G A 哈 21 Er=?

A:

Q: What is the permeable material?

A: Permeability is defined as property of a material by the virtue of it allows the fluid to pass…

Q: Explain what is One-way shear ?

A: One-way shear is defined as:

Q: The resistance of a Solid snoft of diameter d to a hollow Shoft of inner diameter di is the Some…

A: Outer dia of hollow shaft = 20% d +d                                         do =1.2d Inner dia of…

Q: How to know, if structure is unstable?

A: Resistance offered by structure to undesirable movement like sliding, moment and toppling etc is…

Q: identify the structural mechanisms by which lateral loads are resisted by the system?

A: There are mainly two loads gravity load and lateral loads are considered while designing a…

Q: Find the different between trapezium rule and Simpson’s rule and which is better?

A: The trapezium rule and Simpson's rule are both numerical integration methods used to approximate the…

Q: What does a thermal break do

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: What is

A:

Q: Determine the horizontal displacement (mm) of joint C. 300 lb. 300 lb. 13 ft 0080 B 5 ft 12 ft 13 ft…

A:

Q: load and resistance factor design

A: Load and resistance factor design (LRFD) is the method also called as design strength used the term…

Q: What is the flexure formula and tell what the unknown letters represent?

A: Solution: The flexure formula basically gives the internal bending stresses caused by an external…

Q: Describe what happens in the earth when an earthquake occurs.

A: An earthquake is a rapid and violent trembling of the earth's tectonic plates due to shifts or…

Q: give a summary of learning in the analysis of beams under Ultimate Strength Design and how is it…

A: The ultimate strength method provides the actual stress-strain relations of concrete and steel, up…

Q: A trapezoidal channel is to be designed to convey a discharge of 50 m³/sec at a velocity of 2 m/sec.…

A: GivenTrapezoidal channel-Discharge Q=50 m3/sVelocity V=2 m/sbed width to depth ratio-By=0.8side…

Q: flexural tests

A: These tests are used to find the flexural strength of a material.This helps us to know the modulus…

Q: Pressure exerted on a block of wood present at a depth of 30 m under water?

A: Given: Depth of block, h = 30 m

Q: How to determine that a pipe belongs to flexible or rigid pipes category?

A: Answer Rigid pipeRigid pipes are strong that can withstand live load and dead load easily. A rigid…

Q: 4. What's function of movement joints in buildings? Describes how to design them.

A: The function of Movement Joints : 1. A movement joint, also known as an expansion joint is a dynamic…

Q: es of dynamic load

A: A computer programme can load a library into memory at runtime, retrieve the addresses of the…

Q: Where can I find the Structural variables?

A: Structural variables:- Structural variables are physical properties and characteristics of…

Q: The W-beam below is made of A36 steel. La SS(10) m Determine: a. The shape factor (K) 10 mm 1s mm…

A: Solution: Considering the above Diagram of I section y¯=200+10+102=110…

Q: 9.1 A 100-ft-long loose-laid, roof membrane (a = 0.000 150 in/in-°F) will be installed on a flat…

A: solution  Room member L =100 ft Given co efficient of thermal expansion α = 0.000150 in / in - °F…

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.