round to the nearer thousandth when needed.Express 2 meters as inches.

Q: questions by completing the tabulation below. Determine the total area of the lot in sq.m COMPUTED…

A: To find : Total area

Q: A 120-lb cabinet is mounted on casters that can be locked to prevent their rotation. The coefficient…

A: In this question, we will make the equilibrium equations to solve the question. The Cabinet will…

Q: Txs Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an…

A: Given data:- σxA,B=59.2σsA,B=118.5τxsA,B=118.5 Below diagram is given;

Q: Situation C. The lap joint shown below is fastened by four 4-in.- diameter rivets. Shearing stress…

A:

Q: questions by completing the tabulation below. Determine the total area of the lot in hectares.…

A: Data Given: Asked: Complete the solution

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: Size of hollow blocks (LxH) in inches of thickness. Format: 0.00units_x_0.00units any (ex: 0.12in x…

A: Size of hollow block of W thickness in 'mm' (of any thickness) in the format of LxWxH is- L x W x H…

Q: A steep wide rectangular channel takes off from a reservoir having an elevation of 101.2 m. At the…

A:

Q: A plane motion of a particle is described in polar coordinates as R = 0.75 + 0.5t² (m) and 0 = nt²…

A: step 1-

Q: (b) A single test pile, 300 mm diameter, is driven through a depth of 8 m of clay which has an…

A:

Q: For the frame shown, determine the reactions at the supports (support A is a hinged while B is a…

A:

Q: AB kN AC kN 3. Simply supported beam with rectangular section is subjected to the loads shown in the…

A: Finding out normal stresses.

Q: Design a tie column to carry an axial dead load of 600 kN and an axial live load of (1.6X1+2.6X2)…

A: Given  Fy=X2=403MPaFc=X1=67.9MPaDead load=600kNlive=1.6X1+2.6X2Total=600+1.6×67.9+2.6×403…

Q: AP of five terms, the sum of the last 4 terms is 38 and the product of the 2nd and 5th is 70. Find…

A: Given:- sum of last 4 terms =38 product of 2nd and 5th =70 To find:- progression

Q: Problem 2: Draw the shear and moment diagram of the indeterminate beam. 75KN 17KN/m 60KN 40KN 10KN/m…

A:

Q: 3? (KIN) GF? (kN) What is the force in member What is the force in member FE? (kN) What is the force…

A:

Q: 2. An axial load of [A (100)] kiloNewtons is applied to a flat bar [B] mm thick, tapering in width…

A: Given, Axial load P = A(100) = 5(100) = 500KN Length (L) = 5m E = 200GPa = 200×10³mpa b1=120mm b2=…

Q: questions by completing the tabulation below. What is the computed departure of line DE?

A:

Q: Determine the force in each member of the truss

A: ∑MG=0-HA×4 + 5×2 + 94×4 + 212×6=0HA=414.5 kN →∑H=0HA-HG=0414.5-HG=0HG=414.5 kN…

Q: Determine the Inertia (Ix) of the material shown from the X-X Axis (centroidal axis) 180 mm 60 mm…

A: Coordinate of Centroid :  X¯ = A1X1 + A2X2 + A3X3A1 + A2 + A3     = 120×40×60 + 220 - 60 - 40×40×20…

Q: Problem 2. A certain soil sample with cohesion of A kPa, and angle of internal friction is B degrees…

A:

Q: round to the nearer thousandth when needed.Express 86 centimeters as feet and inches.

A: Answer : (1) 86 centimeter as feet We know that 1 centimeter = 0.0328084 feet For  86 centimeter we…

Q: COURSE LENGTH (m) BEARING / AZIMUTH AB 110.80 32°27' BC 83.60 unknown CD 126.90 188°51' DE unknown…

A:

Q: E= 30 LFel=? Y A FeloN 30

A:

Q: Determine the reaction in the support of the beam loaded and supported as shown: 5 kN/m A 10 m B 5…

A:

Q: Using SDM for the frame shown below, determine the following structural parameters. FEM and support…

A:

Q: A pin connected truss is loaded and supported as shown in the figure. Determine the minimum cross-…

A:

Q: 20kN 2m 5m Draw and solve for the shear and bending moment diagram of the structure using Slope…

A: Jcjvk

Q: Situation #1 The compound beam is pin supported at C and supported by a roller at A and B. There is…

A: As per company policy we can only answer first three questions Kindly post other questions as…

Q: The seawall shown below consists of a flat section AB = 3-m with another section, BC,

A: F1 =Force on flat portion      = Pc . A     =γω .hc A      = 9.8153×5 =735.75 KN F2 = Force on…

Q: Hi please answeer replace x=0 y=7 z=8

A: To find magnitude and direction of resultant

Q: A 50-foot coil of 3⁄8-inch diameter copper tubing weighs 9.9 pounds. What isthe weight of 1 foot of…

A: Given data:- The given diameter of copper tube,  3/8 inch The diameter of coil at copper tubing…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.