Answered: rotation of a 12 kg motorcycle wheel is… | bartleby

Related questions

Question

The rotation of a 12 kg motorcycle wheel is depicted in the figure. The wheel should be approximated to be an annulus of uniform density with inner radius R₁ = 27 cm and outer radius R₂ = 33 cm.

Calculate the rotational kinetic energy in the motorcycle wheel if its angular velocity is 120 rad/s in J?

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A uniform disk of mass 500 kg and radius 0.25 m is mounted on frictionless bearings so it can rotate freely around a vertical axis through its center (see the following figure). A cord is wrapped around the rim of the disk and pulled with a force of 10 N. (a) How much work has the force done at the instant the disk has completed three revolutions, starting from rest? (b) Determine the torque due to the force, then calculate the work done by this torque at the instant the disk has completed three revolutions? (c) What is the angular velocity at that instant? (d) What is the power output of the force at that instant?
A frictionless pulley has the shape of a uniform solid disk of mass 2.90 kg and radius 10 cm. A 1.30 kg stone is attached to a very light wire that is wrapped around the rim of the pulley (the figure (Figure 1)), and the system is released from rest. How far must the stone fall so that the pulley has 3.40 J of kinetic energy? What percent of the total kinetic energy does the pulley have?
The uniform solid block in the figure has mass 21.3 kg and edge lengths a=0.754 m, b = 1.33 m, and c = 0.0662 m. Calculate its rotational inertia about an axis through one corner and perpendicular to the large faces. Number Mo Units Rotation axis
The SI unitfor rotational kinetic energy J kg ^2 none W
A uniform disk (1=1/2 mR2) has a mass of 3 kg and a radius of 2m. The disk is mounted on frictionless bearings and is used as a turntable. The turntable is initially rotating at 120 rpm (revolutions per minute, convert it to rad/s). A hollow cylinder has the same mass and radius as the disk. It is released from rest, just above the turntable, and on the same vertical axis. The hollow cylinder slips on the turntable for 0.20 s until it acquires the same final angular velocity as the turntable. (HINT: Note that some of the information given is not needed! Think which conservation law(s) apply.) The final angular momentum of the system is closest to: L = Submit [5] ΑΣΦ Request Answer ? kg. m²/s 4
A 300gr ball and a 700gr ball are connected by a 60cm long, thin rod of mass 100gr. The structure rotates about its center of mass at 100 rotations per minute. Calculate the rotational kinetic energy of the system.
A 2.00-m long rod is hinged at one end. The rod is initially held in the horizontal position, and then released as the free end is allowed to fall. (a) What is the angular acceleration as it is released? (b) What is the angular acceleration when it reaches the vertical position? (c) Which position has the maximum angular velocity (vertical or horizontal)? (d) Which position has the maximum angular acceleration (vertical or horizontal)? (The moment of inertia of a rod about one end is ML2/3.)
A wheel consists of a rim (ring) with a mass of 1.3kg and a radius of 0.45m and four equally-spaced spokes (rods) that run from the center of the wheel to the edge of the rim. Each spoke has a mass of 0.15kg and a length equal to the radius of the wheel. What is the total rotational inertia of the wheel about its center?
A 5kg sphere with a radius of 10 cm is spinning at an angular of 15rads/s. What is the rotational kinetic energy (in j) of the solid sphere? The final answer in 2 decimal places
A 100 g disk with a diameter of 10 cm rotates about an axis through its center of mass with 0.2 J of rotational kinetic energy. What is the speed of a point on the rim of the disk?