RN+10kips 25 kips RN+35 Find Maximum Bending Mement and Shear Force Values and locations. afs afs solve this question with 61 roll number and sectioning and shear force diagram and bending moment diagram

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: Cad drawing and assembly drawing of a trolley jack

A: A trolley jack, also known as a floor jack or hydraulic jack, is a mechanical device used to lift…

Q: Impact velocity equation

A:

Q: LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices…

A: Identify the feature displayed in the picture, and choose from choices below.

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A:

Q: Q/Draw S and B-M D 8 kuim

A:

Q: How will the date code be applied to the assembly? 2. What paper size is the original version of…

A: Here given engineering drawing sheet shows the PRV Blank assembly drawing which consist of various…

Q: ADD MISSING LINES (VISIBLE OR HIDDEN) TO EACH OF THE PROBLEMS BELOW. XX * 30

A: Given: Photographic views: Top view, Front View and Right View.To draw: Missing lines for each…

Q: Which of the following tools is used in both marking and measuring? O Center Punch O Mallet O None…

A: Center punch is a marking tool used to mark center of a hole which is to be drilled. It is not a…

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: In Figure below, the main issue is with the leader representing which item?

A: Given:- An engineering drawing To find: Which representation is wrong

Q: lease write a precise overview/description of the precision tweezer below specifically for each…

A: Given Data : Precision tweezer

Q: What type of scale is 1:20? O Full Scale O Enlargement Scale O Reduction Scale O O O

A:

Q: Scale board

A:

Q: Pls use any CAD software to draw the sectional view of the solid attached in the image below.

A: FindWe need to draw the sectional view of the given object using CAD software.

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2.  There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: In which of the following casting process, the melting pot is an integral part of the machine. * O…

A:

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: machine design 1 question welding check the seam safety Example= Vd. ME Given data

A: For the given material specification, the yield and tensile stress.

Q: Name the feature shown below. 10 00

A: the feature displayed in the picture is extrude

Q: Identify the type of milling operation in which the narrow slots or grooves can be produced into the…

A: Solution:

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: What is compound indexing?

A: Soln:- Compound indexing :- Compound indexing is the operation of obtaining a desired spindle speed…

Q: I need answers to parts 7, 8, and 9, pertaining to the print provided.

A: What is the basic height of this assembly as shown in the section view?Refer the front section…

Q: 1. AISI steel designation for plain carbon steel. 2. In GD&T, what does this indicate 3. A fit…

A: Steel designations are the ways to define the different plain carbon steels.

Q: QUESTION 2 vehicle's tires slip? 25 0.6 m 25 0.6 m 1.4 m Figure 2: A tractor and crate link

A: Given: The weight of the tractor, W = 1.5Mg The coefficient of friction between tyres and ground, f1…

Q: Draw a FBD the tip to tail method please show steps

A:

Q: Direction: Solve the following problems completely. Include all FBD with proper labels. 4 decimal…

A:

Q: By using AutoCAD command draw the following samples with possible fitting. 1- Main door 2- Boiler 3-…

A: Given question: By using AutoCAD commands draw the following : 1. Main Door 2. Boiler 3.…

Q: Q2 Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: Using autocad draw necessary views. Kindly all the views I'll rate your solution

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: ct one or more: Punch down tool is used to pull out the wire into the block hole and cut off the…

A: This question examines / tests the knowledge about the different tools electricians normally use.…

Q: What is called the fit? 1) the difference between the maximum and minimum limits of size, 2) the…

A: Handwritten.jpg

Q: What type of scale is 1:1? Full Scale O Enlargment Scale Reduction Scale

A: Scale factor is the ratio of the length of the drawing to the actual length of the object. The scale…

Q: FGI and FKJ correct but incorrect afterwards.

A:

Q: Produce a 3D solid model of the Guard casing and test boss and produce an assembly of the two parts…

A: Given Guard casing Test boss To find Parts Assembly

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.