ritical section. Use f’c = 3 ksi and fy = 60 ksi. Determine the required spacing of #3 vertical U-stirrup.

Q: steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Given:- Span = 4m Simple Supported beam Tensile stress = 35N/mm2  To find:- w, δmax compressive

Q: (load) Trsmm |00 mm חחףך 125 mm F (load) 150 mm

A: I have determined the value of load P and mentioned complete calculation.

Q: P 5. The steel plate is fastened to the vertical member by five 12-mm diameter rivets. Determine the…

A: Given data:-  No. of rivets, n = 5 Diameter of Rivet. d = 12 mm

Q: Compute the co-ordinates for (Pnb, Mnb) and (Pub, Mub) for rectangular columns using h=24in b=14in…

A:

Q: 3-3 A rectangular section with width b=200mm and depth h=450mm is reinforc with 4 16 of HRB400. The…

A: Width (b) = 200 mmDepth (h) = 450 mmReinforcement of concrete = 4 -16 diameter HRB400Design Moment…

Q: N A F q C B D X 2a a a The figure above shows a static indeterminate beam ABCD. The beam has a fixed…

A: a = (40+40)/50 = 1.6m  q = (40+25)/20 = 3.25KN/m

Q: The building shown in Figure 1 is subjected to an unfactored dead load of 45 psf and an unfactored…

A: DL = 45 lb/ft2LL = 65 lb/ft2 Slab dimension:Longer length, Ly = 30 ftShorter span, Lx = 22 ft, 15…

Q: Use Portal Method: A. Column Shear B. Column Moment C. Girder axial forces, moments and shear

A:

Q: d B E C 654 P₁ 60 1.L F ( H P2 75 5 panels @ 4.50 m = 22.50 m 4.50 m 6.0 m

A: check the stress in member BD, DE, and EG using method of sections

Q: Uniform heavy plate of mass m supported in vertical plane by cable C and hinge A. C m

A: Consider the figure,

Q: Determine the maximum shear stress acting at section a-a of the beam below. 20 mm 4 kN 8 kN 70 mm…

A:

Q: Calculate the internal forces in the bar GF and GD in a roof truss as shown below. For each bar,…

A: Answer  The forces in the bars GF & GD are FGF = -10.62 kN (Compression)  FGD = 3.91 kN…

Q: 12-1. An L2 steel strap having a thickness of 0.125 in. and a width of 2 in. is bent into a circular…

A: L2 steel strap thickness=0.125 in width= 2in Radius of circular arc=600in To find Maximum bending…

Q: ACTIVITY I - MA KE A PRESENTATION A. THE FLOOR SYSTEM OF A CYMNASIUM CONCISTE OF G INCHES THICK…

A: For every building, distribution of the load is fundamental to understand the behavior of the…

Q: 1) Regd: Determine Maximum Shearing Stresses for the 3 segments and eat C 2) Re (2)Solid…

A:

Q: A structure is to be built as shown supporting a uniform load of 18 kN/m. The location for the…

A: Allowable bending stress                                         σ = MyI where M -  calculated…

Q: 8.9 Select the lightest 14-inch-nominal-depth W beam to carry the load shown. Assume A992 steel. (F…

A: The given beam is simple supported with UDL of 1k/ft over the entire span.

Composite Construction

Composite construction is the construction of structures in which two or more materials are used. Regarding structural engineering, composite construction is a construction where two materials are bound together in a technical manner such that both the materials act as a single unit to carry and transfer the load. The motives of composite construction are to increase the structural strength, make structures more aesthetic, and provide a sustainable environment.