4. The heating element in an oven has a resistance of R =32 N. One of thewires connecting the oven to the 220 volt power source is loose, contributing anadditional r = 5 N to the closed-loop circuit. What is the power Poven radiatedin the oven, and what is the rate Peontact at which heat is dissipated at the loosecontact? The looser is the connection, the greater is the resistance r. What valueof r is most likely to cause a fire? Use the computer to make a graph showingPeontact versus r. You may wish to consult the video from the Master SamaraiTech: https://mastersamuraitech.com/loose-electrical-connections-and-heat/

Answered: Image /qna-images/answer/606167cb-d407-4030-9fb1-2225f0fdd4ef.jpg

rires connecting the oven to the 220 volt power source is loose, contributing an dditional r = 5 2 to the closed-loop circuit. What is the power Poven radiated a the oven, and what is the rate Peontact at which heat is dissipated at the loose ontact? The looser is the connection, the greater is the resistance r. What value fr is most likely to cause a fire? Use the computer to make a graph showing Pcontact versus r. You may wish to consult the video from the Master Samarai Tech: https://mastersamuraitech.com/loose-electrical-connections-and-heat/

rires connecting the oven to the 220 volt power source is loose, contributing an dditional r = 5 2 to the closed-loop circuit. What is the power Poven radiated a the oven, and what is the rate Peontact at which heat is dissipated at the loose ontact? The looser is the connection, the greater is the resistance r. What value fr is most likely to cause a fire? Use the computer to make a graph showing Pcontact versus r. You may wish to consult the video from the Master Samarai Tech: https://mastersamuraitech.com/loose-electrical-connections-and-heat/

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 2 wire d.c. ring distributor is fed at A with 220 V. The various loads are 10A at B, 20A at C,30A at D and 10A at E. The resistances of the sections AB, BC, DC, DE and EA are 0.1 £2, 0.05 $2, 0.01 2, 0.025 2 and 0.075 respectively. Determine, a. Point of minimum potential b. Current in each section [Ans.: Point C, 29.04 A, 19.04 A, 0.96 A, 30.96 A and 40.96 A
For a system if the value of peak overshoot is 16 %, then the value of damping ratio o is
Determine the CH2 peak value. Write the values only in four decimal places. the correct answer is 1.9600 please show the solution thank you!
The charging scheme used in Figure is calleda tapered-current charge cycle. The current starts atthe highest level and then decreases with time for theentire charge cycle, as shown. The battery is chargedfor 12 h. Find:a. The total charge delivered to the battery.b. The energy transferred to the battery during thecharging cycle.
please answer with complete solution. thankyou
Calculate the peak voltage across R2 in the diagram R1 = 1 kohm, R2 = 680 ohms, supply voltage is 10V RMS 5.73V peak 10V peak 4.04V peak 1.75V peak
Subject:Circuits IIA 300- kw alternator has an efficiency of 90 % at full load. Calculate the power losses?
( read values &Solve Carefully and Box final answer ) Hint : Enter your answer to the 2nd nearest decimal place.
1-13 Describe Kirchhoff's Voltage Law. Explain how it relates to the principle of the conservation of energy.
In this System your primary element is sending 1v - 5v to your controller and our controller is sending 4mA - 20mA to your final Element. 1) The Primary Element is sending 2.8v. Your controller is reading 2.8v. The Controller sends 5.2mA to the Final Element but nothing changes in your Process Variable. What is wrong? Controller Final Element Transmitter Wire 2) The Primary Element is sending 12v. Your controller is reading 12v. The Controller sends 0mA to the Final Element. What is wrong? Controller Final Element Transmitter Wire 3) the Primary Element is sending 3.4v. Your controller is reading 0v. The Control is not making changes when necessary, what is wrong? Controller Final Element Transmitter Wire
Clear solutions pls. Thank you Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 1 ohms R2 = 10 ohms C1 = 0.007 Farad C2 = 0.008 Farad Vs = 9 Volts Frequency = 6 Hz What is the Total Reactance in ohms?
draw the circuit and solve the following