right side(all trials)left side(trial 1)Sleft side(trial 2)left side(trial 3)mass20.90 g + 50 g =kg20.74 g +100 g =kg20.74 g + 50 g =kg20.74 g +30 g =Data Analysis for Part One2445 words Text Predictions: On16.1kgType here to search2Wweight (N)#3Eposition75.00 cm35.65 cm25.30 cm15.55 cm$4lever arm (m)75.00-50.20 cm:50.20-35.65 cm=mm50.20-25.30 cm =R50.20-15.55 cm =%mm1torque (Nm)406H trial 1trial 2trial 3right side torque (Nm)"expected value"(same as above)(same as above)left side torque (Nm)"measured value"% error

Disclaimer: “Since you have asked posted a question with multiple sub-parts, we will solve the first…

Answered: right side (all trials) left side…

Similar questions

Sam and Joe carry a beam, walking to the right. Calculate the force that Sam exerts, in pounds. The beam's weight is 163 lb. The beam's length is 22 ft. Sam is 5 ft from the back. Joe is 5 ft from the front.
The two objects in the figure are balanced on the pivot. What is distance d?
Clamp Stand Figure 1 4 Leave the knife-edge of the first clamp at the center of mass of the stick and on the fulcrum. Place the second clamp with a hanging mass of 100 g at the 5.0 cm mark (Figure 2). Find the location of the third clamp on the stick with a hanging mass of 150 g that will balance the stick. =390m П. 10 20 30 40 50 Figure 2 69 100 g 150 g
A gymnast with mass 55.0 kg stands on the end of a uniform balance beam as shown in the figure below. The beam is 5.00 m long and has a mass of 250 kg (excluding the mass of the two supports). Each support is 0.700 m from its end of the beam. In unit-vector notation, what are the forces on the beam due to support 1 and support 2? L. (a) F1 = N (b) F2 = N
The figure below shows a claw hammer being used to pull a nail out of a horizontal board where ? = 27.3°. The mass of the hammer is 1.00 kg. A force of 165 N is exerted horizontally as shown, and the nail does not yet move relative to the board. Assume the force the hammer exerts on the nail is parallel to the nail. A hand uses a hammer to pull a nail out of the ground. The head of the hammer is curved and touches the ground at a single point of contact at the center of the head. The nail in the ground makes an acute angle ? clockwise from the vertical. The nail is hooked in the hammer claw 5.00 cm horizontally to the left of the hammer head's point of contact to the ground. The hand pulls the hammer handle horizontally to the right 30.0 cm above the ground with a force vector F.(a) Find the force exerted by the hammer claws on the nail.magnitude kNdirection ° above the horizontal (b) Find the force exerted by the surface on the point of contact with the hammer head.( î + ĵ)…
Determine the additional mass required for stable equilibrium. Meter stick: Xcm = 50.0 cm, m = 150.0 g. Hanger clamp: x= +0.0 cm, m = 16.5 g. (see the figure below) Xec 0.0 cm *** Xfulcrum = 20.0 cm Xcm = 50.0 cm Fee Fe
4. A meter stick has a pivot that is located at (35 cm). On this meter stick weplace 200 g @ 20 cm, 200 g @ 25 cm, 350 g @70 cm and 100 g @80 cm.The meter stick has a mass of 150 g. a. How much mass needs to be placed at 55 cm in order to balance themeter stick.__________________________ b. Where will you put 500 g in order to balance the meterstick?___________________________________ If you could clearly circle the answers I need, that would be great! Thanks!
You place a 5 kg brick at 1.25 m on the left side of a lever system. You place another 5 kg brick at 0.25 m on the left side as well. Where on the right side would you place a 30 kg rock to balance the system? A 0.5 m 0.25 m C 1.75 m D 1.25 m
2.0 kg 4.0 kg d 2.0 m The wooden beam has a mass of 20 kg. What is the distance d that balances the seesaw? 2.0 m 5.0 kg
Calculate the torque produced by the tension T = 20 N at point 0.
Find the resultant of the three forces in the figure 68⁰ 90° 40 N 20N 60N R=120.8 NO R=18.8 NO R=70.8 NO R=100.8 NO