Ri Re Il.25 i 2 R 6 2.25 R 2.5 3 Rg 3.25 Ra i3.5 R i4.5 R1z 5 Rs RiB Ri4 I ,Riz R 15 Ris Rio 14 R13 Ri7 -· R. wm

Q: 1.2 For the circuits of Figure 1.2 sketch von 10 V 12 V -10 V 1-12 V f = 1kHz (a) 10x0 m 5.3 V с It…

A: Given data, 1.2) a) b)

Q: Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the…

A: SCR: It is a semiconductor device from the thyristor family used as a switch. It is on when the gate…

Q: The half - wave rectifier has a load resistance of 0.5 MQ and the input voltage is 5 sinwt V, load…

A:

Q: R R2 R3 A R4 B R5 R6 CO ww ww

A: Given circuit   since the terminals A and B are shortcircuited which means there is no potential…

Q: 6- What is the total resistance of the mixed circuits shown in the following Figure? Note that each…

A:

Q: Draw the drain curve and discuss about the region of operation. When VGS is 4.5V and maximum drain…

A: (a) The curve for drain current s shown below

Q: In the circuit in the figure, the amplitude of the input current is 5 Amps and its phase is 0…

A: For the given circuit the value of the unknown voltage V needs to be calculated and the same can be…

Q: Determine the output voltage for each zener limiting circuit in this Figure? R 20 V 6.2 V -20 V 15 V…

A: During +ve cycle of Vin, Z1 is forward biased and Z2 is reversed biasedFor Vin≤0.7+62=For Vin≤6.9 V,…

Q: For the network in the figure, determine the "Vi" range, which will keep "VL" at 8V and will not…

A: According to question: The minimum value of Vi occurs when  IZ=0&I=IL Therefore…

Q: What is the value of Vgs, when Id is .10 ?constant reference voltage Vdd =12V @

A: For a circuit, The reference voltage is 12V. and The drain current is constant.

Q: Voe 19V Rc 100 n 15 k IGURE 5-42 32. The base bias circuit in Figure 5-42 is subjected to a…

A: Bias current- Bias current is referring to the prime power that is used to basically turn on a…

Q: what is the total resistance

A:

Q: ww 20 Ω a o ww 10Ω ww- 80 Ω 60 2 50 Ω bo

A:

Q: - 8V R₁ = 1.2 k√√2 O u +12v R2= 2.5K O R3=5602 Analyze the circuit using any circuit analysis method…

A: In this question,   We need to calculate the diode current and voltage across the diode?  Voltage…

Q: turn off time is the time

A:

Q: Fill up the below state table by converting the most right two digits of the number 88 72 18 to BCD…

A: According to the question, we need to fill up the below state table by converting the most right two…

Q: In the circuit below, when a 2.2KN load is connected to the output, find the value of the current…

A:

Q: We considered the following strain gauge circuit setup in class: R, R3 strain gauge R2 What would…

A: The sign of the voltage measured across the Wheatstone Bridge will switch from positive to negative…

Q: I hope you make your handwriting clear if you are going to write the solution by hand FIGURE 5-35 Ic…

A: We need to find voltage and current for different regions for given characteristics .

Q: A surge resistor of 4.7 ohm is added to Figure 4-45 in between the rectifiers circuit and the…

A: As the ratio from primary to secondary winding is, 8:1 And we know, Implies, Putting values,

Q: For a simple resistive potential divider, the CRO rating of oscilloscope is 250 V. For the…

A: Given: V0=250 VAmplification range=1050-1175  Apply voltage divider rule:…

Q: How do I create a circuit that does the following. The output voltage Vout is at OV originally. If…

A: According to the question, we need to design a regulator circuit that provides the maximum output…

Q: 1. 'R,=_ kQ R, = 1000 2 R2 = 1 ko' %D 1. Rg = .001 MO %3D

A:

Q: Answer the following Questions referring the circuit in figure 10. ID E-8V + VD- ✈ Si IR R2.2 k2 VR

A: Given,

Q: Given that R=2.42 and that each R dissipates a maximum power of 36w without being spoiled what is…

A:

Q: A strain gauge with a resistance of 250 ohm undergoes a change of 0.150 ohm during a test. The…

A: Given, Strain gauge with a resistance, R = 250 ohm  Change in resistance, ∆R = 0.150 ohm Strain,…

Q: After bridge balance, the value of current in the detector circuit is Rg 5V E D R_ O a. same in the…

A: bridge is said to be balanced if there no voltage across the detector unit .  current through the…

Q: 11-A d.c voltmeter has a sensitivity of 1000 2/V when it measures half full scale in 100V range, the…

A: The voltmeter sensitivity resistance r=1000 Ω/V The half-full scale is 100 V

Q: 1. The JFET is (a) a unipolar device (b) a voltage-controlled device (c) a current-controlled device…

A:

Q: Write down the steps on how to Series Resistors Voltage Division

A:

Q: I need to design a power supply 110v , with an output between 6 and 9v. I did a design and I…

A: According to the question, we need to design a power supply of 110 V, with an output between 6 V - 9…

Current Division Method

The generalized current divider formula is given by the following relation below,