Answered: Review: 1. What is the average…

Review: 1. What is the average deviation of the following measurements? 50 mm, 4.5 cm, 0.03 m, and 3 x 10-5 km? Comment on both the accuracy and precision of these measurements.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

summarize findings. Support statements with references that verify the uncertainty inherent in measurements.
Which of the following is NOT true about constant weighing in the experiment? It involves a cycle of heating, cooling, and weighing. A desiccator is used to avoid moisture to В be absorbed by the sample. A proportionality constant will be c) multiplied to the measured weight to account for loss of water. Constant weight is achieved when two D) consecutive measured weights agree within plus or minus 0.3 mg.
3
The following densities of water were obtained by Student A: 1.07 g/mL, 1.14 g/mL, and 1.13 g/mL. Show how Student A determined the density of water to be 1.11 ± 0.04 g/mL. Calculation for the average = 1.11 g/mL: Calculation for the standard deviation = 0.04 g/mL:
8.0 cm 5.8 cm 3.9 cm 1.5 cm A B C D Figure 2. Developed TLC plate of commercial analgesic and standards Use the data presented in Figure 2 as basis for your answer. The TLC plate used is 5 cm by 10 cm. Note that dot A is for the commercial analgesic, dot B is for the aspirin standard, dot C is for the acetaminophen standard, and dot D is for the caffeine standard. What component/s islare present in the commercial analgesic as confirmed on the developed chromatograph?
A student weighed 10 pennies on a balance and recorded the following masses: 3.112 g, 3.109 g, 3.059g, 3.079 g, 3.025g 3.081 g, 2.504 g, 3.050 g, 3.072 g, 3.064g a)Are there outliers among the masses of pennies? b)Calculate the mean mass of pennies and the standard deviation,withthe outlier(s) excluded. c)Re-write the mean mass of pennies with the precisionindicated
Three trials for this experiment had been conducted and the following are the masses of limiting reactant: 0.285 grams, 0.299 grams, and 0.292 grams. What is the standard deviation for the masses of limiting reactant for the three trials? please show work on how to do.
Question: Assume that a lethal dose of aspirin is 50mg per kg of body weight. How many 1.25 grain aspirin tablets would produce a lethal dose for a 25 pound child? CHOOSE the correct answer listed below. Necessary conversions for dimensional analysis:(lethal dose 50mg=1kg) (1 grain = %3D 64.8mg) (1 tab = 1.25 grain)(1kg = 2.2lbs) • Hint: start by converting 25lbs to kg. You will need to use every conversion to solve %3D this problem.
Design and construct a data table. Be sure to give the table a title.
The tolerance of a Class A 25 mL transfer pipet is +0.03 mL. A student uses an uncalibrated Class A transfer pipet to deliver a total of 125 mL of solution. What is the uncertainty in the delivered 125 mL? mL 0.15 Next, the student calibrates the pipet. The calibrated pipet delivers a mean volume of 24.995 mL with an uncertainty of +0.006 mL. The student then uses the calibrated 25 mL pipet to deliver a total of 124.975 mL of solution. What is the uncertainty in the delivered 124.975 mL? 0.375 mL Incorrect How does the uncertainty in the delivered volume using the calibrated pipet compare to the uncertainty in the delivered volume using the uncalibrated pipet? O The uncertainty in the delivered volume is the same for the calibrated and uncalibrated pipet. O The uncertainty in the delivered volume using the calibrated pipet is greater than the uncertainty in the delivered volume using the uncalibrated pipet. O The uncerainty in the delivered volume using the calibrated pipet is less…
A group of students have a 1000-mL beaker with graduation markings every 50 mL and a volume error of ±1% and they also have a 1000-mL graduated cylinder with graduation markings every 25 mL and a volume error of ±1%. Whichever lab equipment they chose what would the volume error be when measuring 675 mL? Options: 7.15 6.35 6.85 6.75 6.65 6.95 6.45 6.55 7.05 7.25
Standard deviation of data: 206.3, 205.5, 205.8 Mean-205.9