resultant force F due to 4 m 3 m water acting on the 3 m by 6 m rectangular area 6 m AB shown. 6. B D.

Q: Length of beam=5m 6016mm 60 16 mm Section 1-11 WOZ 0.40 m-

A: We know that,  Volume = L×B× H Given,  Length of the beam = 5 m.  Width of the beam= 0.40 m.  Depth…

Q: Calculate the inertia (Ix) of the illustration. 1 3 in 2 6 in -1 in -3 in 3

A: To calculate the moment of inertia of the section, using the parallel axis theorem to find the…

Q: Given that the three bars shown in the accompanying figure are made of the same material, comparing…

A: Given data- The given bars and their conditions have been shown below-

Q: A composite beam is fabricated by bolting two 3.8-in-wide by 8-in.-deep timber planks to the sides…

A: Given data  LAB = LCD = 3 ft ,        LBC = 11 ft  Modulus of elasticity of steel (Es) = 28700 ksi…

Q: Find the R value of a pane of 0.125-in thick glass

A:

Q: Filaments are assembled into the geotextile fabric using either a woven or a nonwoven procedure.…

A: It is given that the filaments are assembled into the geotextile fabric using either a woven or a…

Q: 2 - Reflect & comment on how would you solve the problem if the system is subjected to ground…

A: Answer If the system is subjected to ground motion, we will use the formula  F=-Kx and, while acting…

Q: Referring to the dial gauge shown in Figure , determinea. Accuracyb. Sensitivityc. Range, given that…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Three forces are acting on the eyebolt shown below. All forces intersect at a common point O.…

A: Given data in question  Forces 2500, 3000 & 4000 Angles 45, 25 & 30° To find out  Resultant…

Q: Briefly describe the dye penetrant, X-ray and ultrasonic methods

A:

Q: Define vibrating wire piezometer.

A: Vibrating wire piezometers are used to regulate the pressure of pore water in soils.

Q: Problem #4: [ If the bolt head and the supporting bracket are made of the same material having a…

A: Given:- Bolt head and the supporting bracket are made of same material Failure shear stress = 120…

Q: Draw the HGL and EGL in a venturi meter

A:

Q: A CPC is a type of offset printing pr

A: Printing is the process of reproducing images from an electronic device on paper or another tangible…

Q: CE231 ASSIGNMENT NO.4 ENGR. FRANKLIN M. SALAS BSCEICT-UL, MENGJAIT, THAILAND) Write your name and…

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: Niebel's Methods, Standards, and Work Design by Freivalds, Andris   What is the luminance of a…

A: Given data,  Reflection of surface= 50%  Illumination= 4 fc = 4 foot candle Luminance = ?  Luminance…

Q: For the laser-cut plate shown as the shaded area shown in the first diagram below, calculate the…

A:

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.