Required information Professor Gordon Holloway and his students at the University of New Brunswick went to a fast-food emporium and tried to drink chocolate shakes (p = 1200 kg/m3, u=6 kg/m-s) through fat straws 9.8 mm in diameter and 30 cm long. Take TT = 22/7. The kinetic energy correction factor a is 2.0. A student cut 15 cm from his straw and proceeded drink happily. What rate of milkshake flow was produced by this strategy? The milkshake flow rate is |cm3/s.

Q: Required information A delivery vehicle carries a long sign on top, as in the image. The sign is…

A:

Q: (See Fluids in the News article titled "Where the plume goes".) Air flows into the jet engine shown…

A:

Q: 0.25kg/s of Carbon Dioxide (R = 0.1889 kJ/kg-K, k = 1.289) undergo a certain process in a close…

A:

Q: The Stokes-Oseen formula for drag force Fon a sphere of diameter Din a fluid stream of low velocity…

A: As per given question we have determine is this formula dimensionally homogeneous??

Q: 5. A sample stream of dry gas is being withdrawn from a stack. The stack gases are at 200 °C and 730…

A: a) According to the given data, T= 200∘c and P= 730 mmHgVolume flow rate through filter = Vms+d=Vm y…

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

A: The given information in the problem is shown in the following attached image:

Q: 11. A railroad car of mass 2,000 kg traveling at a velocity v = 10 m/s is stopped at the end of the…

A:

Q: 4. Green checkmark visible in this illustration means that: A) Results are ready for review. B)…

A: The green check mark in the illustration means that C. the meshed has passed the quality check.This…

Q: The tank in the image contains benzene and is pressurized to 350 kPa (gage) in the air gap. The tank…

A:

Q: 4- For the beam shown in Figure, determine the displacements and the slopes at the nodes, the forces…

A: Given:To find:(a) Displacements and the slopes at the nodes.(b) Forces in each element.(c) Reactions…

Q: A uniform rod AB of length L=900mm and mass m=4kg is suspended from a hinge at C. The distance from…

A:

Q: For the process shown in the schematic below, which of the statements is/are incorrect? Feed hopper…

A: 1)b. The process can only work with thermoplastics and not with thermosets due to the thermal…

Q: A pilot weighs 200 lb and is traveling at a constant speed |of 120 ft/s. Determine the normal force…

A:

Q: The turbine on a ship has a mass of 400 kg and is mounted on bearings A and B as shown. Its center…

A: Determine the vertical reaction at bearings if ship undergoes only rolling motion ω1=0.2 rad/s…

Q: Question 2 Two cables are tied together at C and are loaded as shown. Knowing that P = 747, a =…

A:

Q: Problem 3: The crank AB is rotating with a constant angular velocity of 3 rad/s about the fixed…

A: The schematic diagram of the given system is From figure, AC=600 mm AB=300 mm θ=25° Angular…

Q: Starting From Square One 12.00 6.00 2.00 8.00 4.00 9.00 (2 vertical 1 2 3 round 2 Enter the missing…

A:

Q: Design a timber beam (rough cut) made from eastern white pine for the given load in the figure…

A:

Q: Consider the maximum stress when a solid with a circular hole in the center is loaded with an…

A:

Q: Required information A torpedo 8 m below the surface in 20°C seawater cavitates at a speed of 21 m/s…

A:

Q: The plastic pipe AC has a hollow circular cross- section as shown to the right. Determine the normal…

A:

Q: A piece of rubber block is placed in an open rectangular box made out of metal as shown in the…

A:

Q: A piece of rubber block is placed in an open rectangular box made out of metal as shown in the…

A: Please find the answer below

Q: A vehicle is running in a longitudinal way. Suppose the input x(t) is the acceleration, and the…

A:

Q: Question Truck A has a mass of 10,000 kg and is traveling at a speed of 30 m/s. Truck B has a mass…

A: For Truck A mass m=10000kg , velocity v=30m/s For Truck B mass m=5000kg , velocity v=15m/s

Q: Compute the resultant force acting on the pin at C (In kN).

A:

Q: Problem 4. Calculate the tension in the cable, and the reactions at A and C 100 mm 100 mm 300 mm-…

A: Given:-  To Find:-  Tension in cable (T)  Reactions at support A and C  (Roller support is there…

Q: The device shown below uses a hydraulic piston to hoist cars over the range 20 ≤0 ≤90. The piston…

A: Solution: Given Data: s.=0.1 ft/s20o≤θ≤90o   To Find: (a) The expression for the velocity. (b) The…

Q: Find T1, T2 and T3-

A: Given: To determine: T1, T2,T3

Q: How does "MEANT" engineering function, and what is it? Give me the lowdown on what this is and how…

A: Introduction Engineering is the practiced skill of using science to best convert available natural…

Q: p (bar) h (kJ/kg) v (m'/kg) s (kJ/kg-K) State 60 2784 1 5.888 1.5 2262 0.8064 6.102 1.5 467.3…

A: A turbine is a thermodynamic equipment which uses the heat energy to generate useful work. In…

Q: Instruments in airplane A indicate that with respect to the air the plane is headed 30° north of the…

A:

Q: A golfer aims his shot to clear the top of a tree by a distance h at the peak of the trajectory and…

A: According to the given datavo=85ft/sg=32.18 ft/s2R1=150 ftR2=160 ftheight of the tree=40ft

Q: How does science and technology help us?

A: The advancements in science and technology has helped the race of mankind to evolve at a higher…

Q: Sir Isaac Newton measured the speed of sound by timing the difference between seeing a cannon's puff…

A:

Q: Activity 2.4- Newton's Second Law Problems Use the free body diagram method to solve the following…

A: The mass of the ball, M = 60 gram = 0.06 kgThe bouncing speed, vo = 15 m/sThe angle, θ = 20ᵒThe…

Q: Quito, Ecuador, has an average altitude of 2850 m. On a standard day, pressure gage A in a…

A: atmospheric pressure is 101.325 Kpa

Q: Find all functions o for which u(x, t) = 4(x – ct) is a solution of the heat equation 1 ди - o < x <…

A:

Q: A hemispherical container, 32 inches in diameter, is filled with a liquid at 20°C and weighed. The…

A:

Q: At a given instant in an airplane race, airplane A is flying horizontally in a straight line, and…

A: The velocity at A is The acceleration at  A is The velocity at B is .The deceleration at B is

Q: Consider the 4-node isoparametric element. Show that at the origin of the re n = 0: an, y2 - Y4 əx…

A:

Q: Required information A torpedo 8 m below the surface in 20°C seawater cavitates at a speed of 21 m/s…

A:

Q: Saturated steam at 232 °C is used to sterilize a liquid solution. The temperature of the process…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A: Given:To find:(a) Draw Mohr circle for the state of stress.(b) Normal and shear stress on the…

Q: 2. Which of the following comes as the first step in an engineering design process? A. Gathering…

A: An engineering design process is a cyclic process in which there is a continuous process…

Classification of types of corrosion

Corrosion is described as the process in which a certain element is degraded or deteriorated due to the presence of multiple chemicals in the surrounding. Generally, corrosion happens if all the subatomic particles on a metallic object are oxidized, for example, rust on iron structures. In air or water, metals lose electrons to other particles (like oxygen), leading to the formation of an oxide with the metal.