Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A loading car is at rest on a track forming an angle of 25° with the vertical when a force is applied to the cable attached at C. The gross weight of the car and its load is 5495 lb WG, and it acts at point G. Know the tension in the cable connected at C is 5000 lb Tc. Neglect friction between the car and the track. 24 in. 25 in. a B 25 in. 30 in. Determine the distance the car moves in 20 s. (You must provide an answer before moving on to the next part.) The distance the car moves is 1 ft.

Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A loading car is at rest on a track forming an angle of 25° with the vertical when a force is applied to the cable attached at C. The gross weight of the car and its load is 5495 lb WG, and it acts at point G. Know the tension in the cable connected at C is 5000 lb Tc. Neglect friction between the car and the track. 24 in. 25 in. a B 25 in. 30 in. Determine the distance the car moves in 20 s. (You must provide an answer before moving on to the next part.) The distance the car moves is 1 ft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

While digging a small hole prior to planting a tree, a homeowner encounters rocks. If he exerts a horizontal 242-N force on the prybar as shown, what is the horizontal force exerted on rock C? Note that a small ledge on rock C supports a vertical force reaction there. Neglect friction at B. Complete solutions (a) including and (b) excluding the weight of the 17-kg prybar. 242 N A, 1750 mm 15 B 220 mm Answers: (a) Including weight, Fc = i N (a) Excluding weight, Fc = i N
frictionless cylinders A = 2.0 kg and B= 1.0kg. Force P is the smallest force that will lift cylinder A off the horizontal surface. radius of b = 9.95 m 1. Determine the value of P. 2. What is the angle of the tangent line at the point of tangency of the two cylinders.
Problem 1. Find the horizontal force magnitude P needed to start the motion of the block with mass mo in two scenarios: (a) when P is applied to the right and (b) when P is applied to the left. Develop a general solution for each scenario, and subsequently, substitute the values 0= 25°, m = mo = 2.5 kg, µs = 0.40, and μk = 0.35 into your expressions for evaluation. Hgs H k P (a) A mo 0 m P (b) B
3) The cart shown below weighs 45o lb (weight located at CG, at geometric center of cart). If the wheels are locked, and the coefficient of static friction between the wheels and the ground is o.4 (), will the cart slide down the hill? Yes/No: 8 ft 3 ft CG 1 ft 6 ft 15
Blocks mị and m2 are connected by a rope as shown in the figure. There is friction between mi and the wall, where the coefficient of static friction is ls. There is no friction between m2 and the ramp. An unknown force P is applied to mį so that mị is about to slip down the wall and m2 is about to move down the ramp. If the magnitude of the normal force on m2 is n2, find m2, the magnitude of P, the magnitude of the friction force on m1, and the magnitude of the tension force in the rope. The knowns are ls, n2, m1, g, and 0. P = ? Hs rope wall no friction m2 = ? ramp
Two forces act on a massless block. If the force FA is known, what must the magnitude of F3 be in order to keep the block from rotating about point P. B A. FB = 3/5 FA B. FB = 3/4 FA C. FB = FA D. FB = 4/3 FA E. FB = 5/3 FA F P 4 m FB 3 m
A 6-m long ladder has a mass of 10 kg, and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal. How far up along the ladder can a 78-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B. SOLVE ASAP
Q.5) A steel bar OC with attached spring at B and cable at C can rotate freely in a horizontal plane about support at O as shown below. The spring is upstretched when C is coincident with A. Determine the tension T required to hold the steel bar OC in the 40° position shown as a function of k and L. Neglect the weight of the bar OC and the diameter of the pulley at D. 40° L/2 B m T L/2 25°
Block B is on top of an inclined plane and is being supported by Rod AB, which is attached to Block A. The weight of Block A is 40 KN, and the weight of Block B is 80 KN. Force F prevents the block from sliding. Determine the Normal Force N of the surface that supports Block A. Neglect all friction.
Q4.) The 12 kg block A and 10 kg block B are pinned to a rod having negligible mass and resting on horizontal surfaces. A horizontal force P is applied to the rod at end C increasing gradually from zero until motion first begins. a) If the coefficient of static friction between both blocks and each surface is μ = 0.45, determine the value for P at which point motion first begins and describe the motion that occurs in a few brief words. b) If the coefficient of static friction between both blocks and each surface is μ = 0.6, determine the value for P at which point motion first begins and describe the motion that occurs in a few brief words. (Hint: Consider drawing the system as one FBD for this analysis and treat each block as a particle with negligible dimensions) 100 mm 200 mm с Bo 10 kg 25° A 12 kg 12 kg
Two blocks of mass m = 2.00 kg are connected by a vertical string of negligible mass and unknown tension Tm are hanging vertically. The higher one of these two masses is directly attached to another string of negligible mass and unknown tension T that goes over a frictionless pulley of negligible mass and is connected to a third block of mass M = 6.00 kg. The heavier block is free to slide on an incline (of angle 0 = 30.0° w.r.t. the horizontal) with coefficients of kinetic friction of µA = 0.120 and static friction µ,=0.150 between the block and the incline. The system is released from rest. !! M a) Please perform a test to determine which way the system would like to move in the absence of any friction. b) Please perform a test to determine whether the system will be able to overcome the maximum of static friction and be able to move, or remain at rest instead. c) Determine the magnitude of the normal force N exerted on the third block by the incline. d) Determine BOTH the magnitude…
Block 1 (19 kg) is setting on the floor of an elevator. A rope pulls vertically up on block 1 with a tension of 10 N. The elevator is moving downward with a decreasing speed and the magnitude of the acceleration is 2 m/s2.On a sheet of paper, draw the free body diagram for block 1 using the two-subscript notation from class. After completing the free body diagram, enter below each force and its x & y-components. Remember that the x-component is the "i" component and the y-component is the "j" component. NET force on Block 1Fnet1 = i + j N FORCES on BLOCK 1Weight force on block 1 by EarthW1E = i + j N Tension Force on block 1 by RopeT1R = i + j N Normal force on block 1 by SurfaceN1S = i + j N