Required informationConsider the given beam and loading where P= 10 kips/ft. (For S10 x 25.4, S= 24.6 in.)IABDS10 x 25.410 ft3 ftFrom the figures given below, identify the correct bending-moment diagram and determine the maximum normal stress due tobending. (Round the final answer to two decimal places.)Bending (kip-t)MomentBending (kip-t)MomentAE:D:BED22.601756257.59.3751522.60175.6257.59.37515Figure 1Figure 2Bending (kip-tMoment 4Bending (kip-tMomentAEE244166.7511.058 1215244166.7511.058 12Figure 3Figure 4The correct bending-moment diagram is Figure 3The maximum normal stress due to bending isksi. Required informationConsider the given beam and loading where P= 10 kips/ft. (For S10 x 25.4, S= 24.6 in.)IABDS10 x 25.410 ft3 ftFrom the figures given below, identify the correct shear diagram. (You must provide an answer before moving to the next part.)Shear(kip)ShearOkip)ForceForceВAEDB6.756.7515Figure 1Figure 2(kip)OhearForce(kip)ChearForceACE:A5.6257.59.3755.6257.59.37515Figure 3Figure 4

Answered: Image /qna-images/answer/abdd6c1a-4a8e-4644-bc12-3d0fc821c7e7.jpg

Answered: Required information Consider the given…

Required information Consider the given beam and loading where P= 10 kips/ft. (For S10 x 25.4, S= 24.6 in3.) P I B s10 × 25.4 ft 10 ft 3 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B/ Draw shear and bending moment diagram for beam loading as shown in Fig. below: 15 kN/m B 2 m to.5m 21 0.5 m'
Use any of the 3 method of beam deflection find the location and maximum vertical displacement it can produce.
2. A cantilever, made of a certain material, of 2 m length and square section 212 mm on its side, just fails in bending when a point load of 13,252 N is placed at its free end. A beam of rectangular cross section, and made of same material, 150 mm wide and 300 mm deep, is simply supported over a span of 3 m. Calculate: (a) the stress at which the cantilever beam fails in kPa and (b) the maximum concentrated load that the beam can carry at its center without failure in KN. www
Analysis and design of continuous beams: Q1/ Draw the load pattern for the beams B1&B2, If imposed dead load equal to (2.5 kN/m?), and live load equal to (4.8 kN/m?),are applied on the floor ,Assume all beams have the same dimensions and the beams supports as a simply span? Y. = 24 kN / m' ,all columns are (400*400) mm the secondary beam in the middle of span B2? 8m 180mm B1 5m 300mm 200mm B2
compute the maximum deflection of the beam Wu = 2.12 kip lft P₁ = 19.4 kips ↑R= 10 ft = 27.008k 27.008 18.4 kips 2.12 kips/ft | L 20 ft -12.592 5.808 164.08 R= 50.752k 14.96 L -33.792 8ft -67-84 O SHEAR MOMENT
I'm trying to solve this Statics exercise, but I'm getting the wrong answer in every approach I made. How can I solve it?
5) Choose the most economical steel wide flange section for a fully braced beam when Z, required is 279 in?? (see the provided reference).
The simply supported steel beam shown is fabricated from an American Standard S18 x 54.7 section. F -4/2- Hmm Given: • L = 16 ft • 9。 = 5 kip/ft ♦ F = 9 kip L qo TII /7777 1
None
Draw the shear force diagram for the following beam along with calculation of shear force and in diagram write the accurate values..
The simply supported beam consists of a W14 x 34 structural steel wide-flange shape [E = 29,000 ksi; / = 340 in.4]. For the loading shown, use discontinuity functions to compute (a) the slope of the bearn at E and (b) the deflection of the beam at C. Assume wo = 12 kips/ft, wcD = 4.0 kips/ft, LAB= 8.0 ft. LBc= 8.0 ft. Lco - 11.0 ft. LDE = 4 ft. Answer: (a) 8E= (b) vc= B LAB Wo LBC C rad in. WCD LCD D LDE E X
i need clear ans and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛