Required: Draw the front projection, the left side projection, the horizontal projection

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: Draw the FRONT VIEW, TOP VIEW , SIDE VIEW of the figure below • Draw the SURFACE DEVELOPMENT of the…

A:

Q: What are 1-, 2-, and 3-point perspectives? Draw cubes of different sizes using 1-, 2-, and 3-point…

A: Approach to solving the question: drawing, constructing of answer Detailed explanation: Examples:Key…

Q: For the following figure assume the box as 10 mm and sketch the following view using CREO PARAMETRIC…

A:

Q: Do the auxiliary view of this drawing

A: According to the details provided in the question, we need to calculate the auxiliary view. the…

Q: What is the sketch of the right face

A:

Q: Differentiate between perspective projection and orthographic projection also write the name of…

A: Difference between Perspective and Othrographic projection. Sr. No Perspective projection…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: What are the four basic steps of creating a circular shape in perspective? Using any digital medium,…

A:

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: Q) Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A: Solution:

Q: Which of these projection methods is known as multiview drawing? Select one: O A. Isometric…

A: Orthographic projection is projection method to represent a 3D object in set of 3 2D drawings to get…

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: The top one (first drawing) is a top view. The second one or lower one is a side view. Please draw…

A: given : top and side view

Q: What type of drawing is shown (the bottom of the object is horizontal, all lines going towards the…

A: LETS define each one of them   ISOMETRIC DRAWING: Isometric drawing is just a 2D representation of a…

Q: draw the top , left , front view?

A:

Q: PART-A (Sectional View - SKETCHING) 1. Reproduce all two views given and add/complete the sectional…

A: Given Diagram To find Sectional views

Q: Conjecture the introduction of first angle orthographic projection in design.

A: The conjecture first angle orthographic projection in design.

Q: 7. What is the part’s over all depth?_______________________ 9. Which line does in the top view…

A: Solution     7. The part’s overall depth 1.50

Q: The part view should.com RANCES be the same CHD APPVD MIG GA as picture. 2- The color is RGB as DWG…

A: Find Draw the given object using the drawing.

Q: What is the difference between the terms "perspective projection" and "orthographic projection"?…

A: Explanation: Prospective projection: The perspective projection is a linear projection where three…

Q: Question 2 ( When creating a solid model part intricate geometry of your part, s True

A: Solidworks or ansys is a software where simpler and more complex designs can be drawn with each…

Q: what is the ybar distance(distance from bottom edge of triangle to centroid)?    options:   40/3…

A: Given, Right-angled triangle of, Base, b=20 in Height, h=9 in

Q: The part view should be the same as picture. 2- The color is RGB as 0,220,100. 3- Should use the…

A: Find Draw the given object using the drawing.

Q: ZATION & ENGINEERING Design GraPhics with AuGmented REALITY

A: Sectional view

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Q: PART-A (Sectional View - SKETCHING)1. Reproduce all two views given and add/complete the sectional…

A: Given Object To find Views

Q: Sketch the isometric figure of the given views below. Thank yo

A:

Q: Desired / sketch of the front projection, the left side projection, the horizontal projection

A: Required views Front view, Left hand side view and Top view of the given isometric view are drawn on…

Q: Hello, I was just wondering how you find hte angle of the blocks to 45 degrees? Thank you!

A:

Q: A00007: Drafting Competencies - To create drawing view B' it is necessary to select drawing view 'A'…

A: Break view in the solidworks is used to display the larger drwaing in smaller drawing sheet by…

Q: In step 4, it should be the A and not the y right? So it should be FBD divided by 4.04 which is the…

A:

Q: what is the procedure of making V- block rectangle??

A: V blocks  are made up of cast iron  with a 120 degree channel rotated 45 degree from the sides which…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.