Required: Determine if each structure is unstable, externally statically determinate, or externally statically indeterminate. If the structure is externally statically indeterminate, state the degree of indeterminacy. If the structure is unstable, describe in words and with a drawing, the mechanism of instability. (a) (c) (d) Note: Joint at center of structure is fixed (b) Note: Joint in center is a roller

Required: Determine if each structure is unstable, externally statically determinate, or externally statically indeterminate. If the structure is externally statically indeterminate, state the degree of indeterminacy. If the structure is unstable, describe in words and with a drawing, the mechanism of instability. (a) (c) (d) Note: Joint at center of structure is fixed (b) Note: Joint in center is a roller

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E Ук 1 kN 1m H F Figura 3. Cercha 3. 2.Determine the force in the elements ED, EH, and GH of the reinforcement (see Figure 4), and establish whether the elements are in tension or compres- sion. (Use the method of sections). Figura 4. Cercha 4. 50 kN 40 kN -2 m -2 m- -2 m- 1.5 m -30 kN 1.5 m B 40 kN 1.5 m
1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E K 1 kN 1m H M F
The flat truss in the figure below is under the action of three external loads P, Q and S, and is supported under pins A and B. The weight of the truss is negligible in relation to the applied loads. Read the following statements and then check the correct alternative. 1)the supports provide exactly the amount of links needed to keep the structure in balance2)the corresponding reactions involve three unknowns that can be determined through equilibrium equations.3)this is a situation where the rigid body is completely bound4)reactions are statically indeterminate which ones are correct?
Subject is structural analysis Please show each steps to the question and make it easy for me to understand. Explain the diagram
The static indeterminacy of the structure shown below is G F Hinge. С E B (A)Unstable (B) Stable, determinate (C) Stable, 5th degree indeterminate (D)Stable, 3rd degree indeterminate
The state of strain at the point on the member has components of Px = 180(10-6), P y = -120(10-6), and gxy = -100(10-6). Use the strain transformation equations to determine (a) the in-plane principal strains and (b) the maximum in-plane shear strain and average normal strain. Ineach case specify the orientation of the element and show how the strains deform the element within the x–y plane.
The following free body diagrams are unstable. Determine the ff for each FBD a. The equation showing that it is UNSTABLE (R-3N or B+R-2J must be less than 0) b. Make the member stable by only removing a member (no adding of supports and no adding of members). Show that it is STABLE by showing that (R-3N or B+R-2J is => 0)
In the following beams kB=? k (stiffness)
Determine if the given structure is statically determinate, statically indeterminate or unstable.
I need the answer as soon as possible
don't answer the X figure, just answer the d and e
b) A cylindrical rod AB is made of aluminum is connected at B to a brass qylindrical rod BCD as shown in Figure 8. The shear modulus, G of aluminum rod AB is given by 27 GPa and the brass rod BCD of 39 GPa. The torsional reactions, TA and Ts are located at the ends of A and B, respectively. Given the portion CD of the brass rod is hollow and has an inner diameter of 40 mm, examine the angle of twist at A. 60 mm Tg = 1600 N - m 36 mm TA = 800 N m 250 mm 375 mm A 400 mm Figure 8