Replace the two cable tensions which act on the pulley at O of the beam trolley by two parallel forces which act at pulley connections A and B. The forces are positive if up, negative if down. Answers: FA- 1 205 mm 160 mm 205 mm 6.5 KN 4.5 KN Com KN

Q: Compute the combined moment of the two 90-lb forces about (a) point O and (b) point A. The moment is…

A: (a) To find: The moment about the point O. Given: The distance is a=4.8 in and b=2.9 in. The force…

Q: The square gate AB is held in the position shown by hinges along its top edge A and by a shear pin…

A: d=4.5 ftArea of gate=1.8*1.8density of water,

Q: Please show magnitud and direction for every member forces) Use the method of MEMBERS to determine…

A: Force F = —1500 lb

Q: The beam with riveted bracket is subjected to the couple and a force as shown in figure, and their…

A: The reactions at point A can be determined as,

Q: A truss bridge is loaded with point loads according to the figure. Determine the normal force in the…

A: Step 1:Step 2:Step 3:

Q: The Free-Body diagram for joint C is drawn assuming that all internal forces are in tension. Solve…

A: Given

Q: 2.0 m 100 kg 2.0 m 0.5 m 15 m 1.5m The pulley at E is frictionless. Point B is a pinned connection;…

A:

Q: Given: A set of four forces act at corners of a parallelpiped block, as shown below. Find: a)…

A:

Q: Show all Free Body Diagrams   A) Use the Method of Joints to find the forces in AB and BC.…

A: Given:

Q: Replace the loading shown by a single equivalent force. Specify the magnitude and direction of this…

A:

Q: Consider the clamping device used to lift a 55 gallon drum, as depicted in the accompanying figure,…

A:

Q: 2a. If the load intensities w1=82 N/m, w2=176 N/m, and w3=102 N/m, determine the total moment (in…

A:

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 195 lb, is…

A: Draw a diagram for the problem. Here, O is the origin, θ is the inclination of the force F with the…

Q: A machine component is subjected to the forces and couples shown. The component is to be held in…

A:

Q: 3. Determine the magnitudes of the pin reactions at A and C. Neglect the weights of the members. 800…

A:

Q: 2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force…

A: The force applied to the handle is, P=100 N Length of the handle is, L=30 cm

Q: The system consisting of the bar OA, two identical pulleys, and a secti shown in the figure.…

A: The free-body diagram is as follows-

Q: Take a "cut" at H (draw a proper FBD) and determine the forces at H.

A: draw FBD of gievn figure

Q: Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces…

A:

Q: 2. Find the horizontal and vertical forces at Point C as it acts on Member BD.

A:

Q: Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.54-lb force about…

A: Given date:- Force (F) = 0.54 lb

Winding and Constructions

Alternating Current (AC) winding is generally of the 3-phase type due to the inherent advantages of the 3-phase machine. Armature coils must be connected to the yield balance (equivalent in magnitude and 2/3 of the series phase difference of the rod) 3-phase electromotive forces (emf). The armature should be divided into step-bands to start with slots around the perimeter.In the construction of AC machines, the frame is used as an external protective shield to protect it from environmental conditions. The frame also serves as the outer perimeter, allowing the interior to be easily placed. The static state section of the devices is the stator winding attached stator.