What is the major difference between a two way flat slab and two way flare plate **Quiz #7 - Sitecast Concrete Framing – Chapter 14****Specify a slab finish for each of the following situations:** - a. A structural slab over which terrazzo will be installed.- b. A sidewalk.- c. An inclined outdoor automobile ramp in a snowy climate.- d. A factory floor.**Slab Finishes:**- a) Color Chip Finish- b) Stamped Finish- c) Broom Finish- d) Steel Trowel Finish**Question:** What does a curing compound do?- **Answer:** Curing compounds are used to help prevent shrinkage cracking by reducing the evaporation of water from the concrete.**Question:** What is the major physical difference between a two-way flat slab and a two-way flat plate?---**B. True-False Questions**1. Welded wire fabric reinforcing should be cut completely at control joints in a concrete slab on grade. ( )2. Floating can be done as soon as the straightening operation is concluded. ( )3. The center portions of form ties are temporarily embedded in a concrete wall. ( )4. Wood dowels are never used to bond a concrete column to its footing. ( )5. Concrete columns are often cast in paper (SONO) tubes. ( )6. The column grid supporting a two-way flat plate can be somewhat irregular in its spacings. ( )---**C. Multiple Choice Questions**1. Column bars are offset at the top: - a. To bring the column back into vertical alignment - b. To overlap the beam reinforcing - c. To overlap the reinforcing for the column in the next story - d. To compensate for curing shrinkage of the concrete - e. To allow for the thickness of the column ties(Note: This transcription does not involve graphs or diagrams.)

Both Two way flat slab and two way flat plate are structural systems used in building construction…

Answered: rence between a two way flat slab and…

Engineering

Civil Engineering

rence between a two way flat slab and two way flare plate

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What is the difference between rubble and ashlar stone used for wall construction?

A: Rubble is broken stone and naturally found rubble in the soil is known also as 'brash' (1)…

Q: Answer fast

A: To solve the given problem, which involves designing the slab system and showing reinforcement…

Q: What type of reinforcement is used to prevent erosion on slopes?

A: Approach to solving the question:Methods of reinforcing slopes to prevent erosion were identified…

Q: What appearance groups are established for the outer veneers of construction plywood?

A: Outer veneers used for construction purposes are classified into five groups based on their…

Q: Where does the foundation walls cracks occurs?

A: The complete or incomplete layers of concrete that get separated are termed as cracks. These cracks…

Q: What are the basic components of the reinforcing earth construction?

A: basic components of reinforcing earth construction are : 1- Soil 2- Reinforcement 3- Skin

Q: Define metamorphic foliation. Under what kind of stress does metamorphic foliation form?

A: Foliation:- If flat or elongated minerals within a rock are compressed and aligned, foliation is…

Q: What size does an opening in concrete have to be before a deduction is made from the volume of…

A: Where there is an opening in a form system, no deduction is made from the total area of the forms if…

Q: How do you detect subsurface crack

A: Subsurface cracks are difficult to detect since they are not visible from the surface. Subsurface…

Q: Which of the following represents the effective slab width for the composite beam (Beam 1)…

A: For the beam (beam 1) highlighted in the figure, the span of the slab it needs to support is,…

Q: 4.2 Explain the difference between a "flat slab" and "flat plate" framing system. Draw a schematic…

A: Flat slab and flat plate

Q: An architect wants to design a concrete floor with a typical column spacing of 38ft, and there is a…

A: (Column spacing), span = 38 ft Need to find out Minimum slab thickness?

Q: What is the minimum thickness for a residential slab?

A: A concrete slab is normally used for the floor system of industrial or residential structures. It…

Q: how is a foundation post proyected from the moisture in the concrete support

A: The way by which protection of foundation post is done from moisture in the concrete support.

Q: Draw from memory a detail of a typical slab on grade and list the steps in its production.

A: Solution: Production starts with: 1. Excavation and compaction of the subgrade. 2. Placement of edge…

Q: Why are tapes sometimes used with sealants in joints?

A: For complete installation of sealants ,backup materials are required . Sealant's depth is…

Q: Per ACI 318, what is the minimum slab thickness of an edge bay slab (one end continuous) that spans…

A: As per ACI 318, what is the minimum slab thickness of an edge bay slab (one end continuous) that…

Q: Describe about the Installation procedure of Excavation Bracing?

A: Deep excavations with vertical sides need lateral supports to prevent cave in of the soil and to…

Q: What will prevent bitumen from adhering to a concrete wall?

A: Bitumen is naturally occurring substance . As well as Bitumen is obtained as residue after…

Question

What is the major difference between a two way flat slab and two way flare plate

**Quiz #7 - Sitecast Concrete Framing – Chapter 14**

**Specify a slab finish for each of the following situations:**
- a. A structural slab over which terrazzo will be installed.
- b. A sidewalk.
- c. An inclined outdoor automobile ramp in a snowy climate.
- d. A factory floor.

**Slab Finishes:**
- a) Color Chip Finish
- b) Stamped Finish
- c) Broom Finish
- d) Steel Trowel Finish

**Question:** What does a curing compound do?
- **Answer:** Curing compounds are used to help prevent shrinkage cracking by reducing the evaporation of water from the concrete.

**Question:** What is the major physical difference between a two-way flat slab and a two-way flat plate?

---

**B. True-False Questions**

1. Welded wire fabric reinforcing should be cut completely at control joints in a concrete slab on grade. ( )
2. Floating can be done as soon as the straightening operation is concluded. ( )
3. The center portions of form ties are temporarily embedded in a concrete wall. ( )
4. Wood dowels are never used to bond a concrete column to its footing. ( )
5. Concrete columns are often cast in paper (SONO) tubes. ( )
6. The column grid supporting a two-way flat plate can be somewhat irregular in its spacings. ( )

---

**C. Multiple Choice Questions**

1. Column bars are offset at the top:
- a. To bring the column back into vertical alignment
- b. To overlap the beam reinforcing
- c. To overlap the reinforcing for the column in the next story
- d. To compensate for curing shrinkage of the concrete
- e. To allow for the thickness of the column ties

(Note: This transcription does not involve graphs or diagrams.)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

Step 2: Differences

Step 3: Diagram

Solution

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The Advantages and disadvantages of Flat Slab System
how to draw the beam load for a combined one and two way slab
4.8 Refer to the following table from ACI Code to determine the maximum spans or minimum thickness for the multi-span one-way slabs shown the following questions. RECESS 2%* AT BALCONY EDGE TABLE 9.5(a) - MINIMUM THICKNESS OF NONPRESTRESSED BEAMS OR ONE-WAY SLABS UNLESS DEFLECTIONS ARE CALCULATED Member Solid one- way slabs SPAN? CANTILEVER Beams or ribbed one- way slabs Minimum thickness, h One end Both ends Simply supported continuous continuous Cantilever Members not supporting or attached to partitions or other construction likely to be damaged by large deflections 1/20 U24 0728 1/10 4/16 /18.5 021 Notes: Values given shall be used directly for members with normalweight concrete and Grade 60 reinforcement. For other conditions, the values shall be modified as follows: a. Choose a uniform slab thickness for all spans in the following diagram. At the cantilevered balcony, keep the same bottom of slab level for ease of formwork. o pa po 7.4' 26:0 48 For lightweight concrete having…
Does one type of diagonal crack occur before the other?
Discuss the factors influencing the selection of lining materials for open channels?
4.7 The cross section of a conventionally reinforced concrete one-way slab is shown below. Using ACI Table 9.5(a), answer the following questions: 5'-0" CANTILEVER TI 23-0 END-BAY T2 SPAN L3 INTERIOR-BAY a. What is the minimum slab thickness at end bays (T2)? Member Solid one- way slabs BM WIDTH Beams or ribbed one- way slabs TABLE 9.5(a)- - MINIMUM THICKNESS OF NONPRESTRESSED BEAMS OR ONE-WAY SLABS UNLESS DEFLECTIONS ARE CALCULATED Simply supported 23-0 END-BAY 12 €/16 CANTILEVER Minimum thickness, h Both ends One end continuous continuous Cantilever Members not supporting or attached to partitions or other construction likely to be damaged by large deflections 1/20 024 U/28 U/10 d/18.5 (21 €/8 Notes: Values given shall be used directly for members with normalweight concrete and Grade 60 reinforcement. For other conditions, the values shall be modified as follows: a) For lightweight concrete having equilibrium dersity, we, in the range of 90 to 115 loft, the values shall be multiplied…
14.4 Identify the type of masonry block shown below
Describe the principles of soil reinforcement techniques?
Question 8 A sample slab section view is shown below: *4 0 10" EW 30 Felt Joint El. See What should be the correct reinforcement configuration in plan view for this slab? What should be the correct reinforcement configuration in plan view for this slab? 10" 10" 10" 10"- #4 bars 10"- 10" 10" 10" #4 bars 10"- # 4 bars 10"-
ONE WAY SLAB CONTINOUS USING TABLE COEFFICIENT OF BS8110