Answered: reliability = 99.99999%, determine the…

Engineering

Electrical Engineering

reliability = 99.99999%, determine the amount of outage in minute measurement. a) 5.26 b) 0.00526 c) 0.0526 d) 0.526

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Related questions

Q: (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R=30 Ohm resistor…

A: Given, A controlled half wave rectifier, Vrms= 240V f = 60Hz R = 30 ohm

Q: Required information Problem 03.093 - The dc output voltage in the half wave rectifier The half-wave…

Q: A single phase half wave controlled rectifier has RL load. Write the following a) Draw its circuit…

A: As per the guidelines of Bartleby we supposed to answer first three subparts of the question for…

Q: I need help with (d) . Thanks 1. Consider a half-wave rectifier circuit with a resistive load of 25…

Q: A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The…

A: Given Three phase full wave rectifier shown Vm=311.128 vThe load…

Q: Check all the correct statements. The forward voltage in diodes is larger than its reverse voltage.…

A: 1. The forward voltage in diode is larger than it's reverse voltage To "turn on" and lead current…

Q: 1) The following is not an example of a Thyristor a) A Silicon Unilateral Switch b) A TRIAC c) A…

Q: Can you please explain pinch off voltage and go into more detail about how you found VP? thank you

A: The pinch off voltage Vp is the value of drain to source voltage (Vds) at which the drain current…

Q: the line frequency is 60 Hz, the output frequency of a center-tapped transformer full-wave rectifier…

Q: Convert following number in the given radix system. (a) (1010.011)2 to (…………)10 (b) (0.513)10 to…

A: a) Convert base-2 to base-10 To convert base-2 to base-10, multiply with their weights.…

Q: An analog or digital meter displays what quality of voltage or current in AC? (A) Peak (B)Average(C)…

Q: Could some please provide an explanation for VL why 15 and 1.33

Q: in zeq 1 where did you get 210.949 from?

A: Student is asked to explain from where did get ZB 210.949 from?

Q: B. Plot the input and output waveforms, one above the other, for each of the three circuits below.…

Q: (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R= 30 Ohm…

Question

If reliability = 99.99999%, determine the amount of outage in minute measurement.

a) 5.26

b) 0.00526

c) 0.0526

d) 0.526

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The input to a full-wave rectifier is 20 V AC (RMS). The load resistor is 20 ohms and rectifier losses are 4W. The ripple factor of the rectifier is: O A. 0.96 OB. 0.33 O C. 0.48 O D. None of the other choices are correct O E. 0.75
Solve it without using AI
I need the correct expert solution with explanation of the steps of the solution and the abbreviations, please.
The efficiency of any real wind turbine O a. can be more than 59.3% O b. can be less than 59.3% O c. is nearly 100% O d. is always equal to 59.3%
Fifty years into the future, the way we will probably make base load energy include(s) Select one: A. Solar B.Fission C.Fusion, fission and solar D.Fusion
Question (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R=30 Ohm resistor (a) Determine the delay angle such that the average load current is 2.5A (b) Determine the power absorbed by the load (c) Determine the power factor.
What is CEMF?
Question 2. Considering this figure. The firing angle is 45°, the motor current is 10 A, and the supply voltage is 110 v. 0₁ 0₂ 90 (a) Draw the waveforms of v, Vo. io. isi, iDi, and i. (b) Determine the power taken by the dc motor. (c) Determine the supply volt-amperes and supply power factor. Assume that the converter is lossless. (d) Determine the rms value of the SCR current and the diode current.
The input to a full-wave rectifier is 30 V AC (RMS). The load resistor is 10 ohms. The DC power at the output is: O A. 73 W O B. 18 W C. None of the other choices are correct D. 36 W O E. 146 W
According to the nec table 250.55 what would the deman load be for two ranges one 14 kw and one 16 kw
The power output of the half-wave rectifier is rated at 102.4 W with a load resistor of 40 ohms. The RMS voltage at the output is: O A. None of the other choices are correct O B. 12.5 V O C. 102 V O D. 25.5 V O E. 51 V
A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The load is purely resistive of value 52. The DC and RMS output voltages are respectively equal to: Secondary 太D太D,太D, 太D。太De太D, b. Select one: O a. 180V, 240.2V O b. 514.6V, 515.04V O c. 180V, 197.2V O d. 220V, 249.2V