Refrigerant-134a enters the compressor of a cooling system as superheated vapor at 0.18 MPa and 0°C with a flow rate of 0.15 kg/s. It exits the compressor at 0.8 MPa and 60°C. Post compression, the refrigerant is cooled in the condenser to 28°C and 0.7 MPa. Subsequently, it's throttled to 0.16 MPa. Neglecting any heat transfer and pressure drops in the pipelines between the components, represent the cycle on a T-s diagram concerning saturation lines. Calculate: (a) The rate of heat extraction from the cooling area and the energy input to the compressor. (b) The isentropic efficiency of the compressor. (c) The Coefficient of Performance (COP) of the cooling system.

Refrigerant-134a enters the compressor of a cooling system as superheated vapor at 0.18 MPa and 0°C with a flow rate of 0.15 kg/s. It exits the compressor at 0.8 MPa and 60°C. Post compression, the refrigerant is cooled in the condenser to 28°C and 0.7 MPa. Subsequently, it's throttled to 0.16 MPa. Neglecting any heat transfer and pressure drops in the pipelines between the components, represent the cycle on a T-s diagram concerning saturation lines. Calculate: (a) The rate of heat extraction from the cooling area and the energy input to the compressor. (b) The isentropic efficiency of the compressor. (c) The Coefficient of Performance (COP) of the cooling system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hello, please solve this problem, Thank you very much
Thermodynamic
In refrigeration process, a region is cooled and the temperature was maintained at -15oC. The cooling water used in the refrigeration is 25oC. If the refrigerant is HFC-134a, and the heat transfer temperature difference is 10oC, Calculate COP (ω) and mass flowrate for a vapor-compression cycle if the rating of the refrigeration process is 100,000 kJ/h and the efficiency of the compression is 0.75.
P
A vapor-compression refrigeration machine uses refrigerant-134a as much as 2 kg/min with operating conditions leaving the evaporator at a temperature of -14°C and a condenser pressure of 0.8 Mpa. Determine the COP value and cooling load of the machine.
Q14//A surface condenser receives exhaust steam at 0.14 bar from an engine developing 180 kW. The circulating water enters the condenser at 15°C and leaves at 40°C. The final temperature of the condenser steam is 50°C. If the engine consumes 9 kg of steam per kW per hour, determine the quality of the steam entering the condenser, if the weight of circulating water per hour is 31600 kg. (Answer: x=0.85) ****
A refrigerated room is kept at −18◦C by a vapor-compression cycle with R-134a as the refrigerant. Heat is rejected to cooling water that enters the condenser at 14◦C at a rate of 0.35 kg/s and leaves at 22◦C. The refrigerant enters the condenser at 1.2MPa and 50◦C and leaves at the same pressure subcooled by 5◦C. If the compressor consumes 5.5 kW of power, determine (a) the mass flow rate of the refrigerant, (b) the refrigeration load and the COP, (c) the second-law efficiency of the refrigerator and the total exergy destruction in the cycle, and (d) the exergy destruction in the condenser. Take specific heat of water to be 4.18 kJ/kg·◦C.
A gas refrigeration system utilizing air as the working fluid possesses a pressure ratio of 3. The air is directed into the compressor at 5°C. The high- pressure air is then cooled down to 40°C by rejecting heat to the ambient environment. The refrigerant exits the turbine at -85°C and subsequently absorbs heat from the cooling area prior to its entry into the regenerator. The mass flow rate of air is 0.45 kg/s. Given that the isentropic efficiencies are 82 percent for the compressor and 87 percent for the turbine, and using constant specific heats at ambient temperature, find: (a) The effectiveness of the regenerator. (b) The rate at which heat is extracted from the cooling area. (c) The Coefficient of Performance (COP) of the cycle.
An ammonia refrigeration compressor takes its suction from the evaporator at a temperature of -20oF (-28.9oC) and a quality of 95%. The compressor discharges at a pressure of 100 psi (689.5 kPa), liquid ammonia leaves condenser at 50oF (10oC). Properties of Ammonia: At 689.6 kPa (Tsat = 13.3oC) h = 1,568 kJ/kg; s = 5.7676 kJ/kg.K At 10oC: hf = 246.531 kJ/kg At -28.9oC by interpolation hf = 68.5 kJ/kg; hg = 1424.5 kJ/kg sf = 0.49366; sg = 6.0452Find the COP. a. 4 b. 4.25 c. 5 d. 5.25