Refer to Problem 8.12. Given k, = 4× 10-S m/min and k, = 1 × 10-5 m/min, calculate the rate of seepage through the dam (m/min/m) using Schaffernak's %3D solution.

Q: 15. Compute the resultant of the three forces shown in the figure. A. 894.32 N B. 836.90 N C. None…

A:

Q: 1 (AD) = St FIG. 7.13 TABLE 7.6 Segment AB BC 75 CD ED M₂M -dx EI B ABCD B 150 kN Į с (b) Real…

A: Calculate the vertical deflection at D using virtual work method

Q: Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on the…

A:

Q: b) Air at 30°C flows through a 70 m long, 2 cm x 2 cm rectangular cross section pipe as shown in…

A: given temp = 30 'c length = 70m size =2cm*2cm velocity = 2m/s angle = 35'c to find  given above 4…

Q: 2-am *pin is supported at C •AB is a single hydraulic cylinder •limit of arm DC (horizontal…

A:

Q: Group A D1 = 130 mm S=0.8 D2 = 6 mm h1= 45 mm Weight of mass = 6 kg Weigh Piston D₁ 04 What is the…

A: GIVEN :   D1=130 mm   D2 = 6 mm   h1 = 45 mm     W =  6 kg    S = 0.8   ρ =1000  kg/m3  To  find :…

Q: 3- Find the value of resultant R, if T=600N, P=450N, F=20ON, B=60°, a=40°.

A: Consider the free body diagram of the given force system. Resolution of forces in x-direction is…

Q: Using the triple scalar product to determine the moment of the 750 N force about lineOC, you could…

A: To choose the position vector that can not be used to determine the moment of the 750 N force about…

Q: 30 KN lokN/M 2m -2m 6m VA To find the nipport reations, let us apply the equeilibrium of equation 4…

A:

Q: (5D3 + 3D2 — 32D + 12)у — 0 | A. y = c1e-2* + Cze¬0.4* + C3e3* B. y = c,e2* + cze0.2x + Cze-3x C. y…

A:

Q: 03 Figure 03 shows an overhead crane truss supported by pin and roller supports at point A and E.…

A:

Q: I6 とIPS I: 200 in4 エ=200in4 THT I=300 in 6ft 12f ナメ9

A:

Q: The resultant of the two forces has a magnitude of 932 N. Determine the magnitude of P using Law of…

A:

Q: Truss Energy: find t Daft 6 ft 2.22 kips 2225/1 Kips 8ft Vertical deflection at B using Virtual Work…

A:

Q: H.w:-prove that 01 σe = Ao A

A: Ture stress is the ratio of force applied to the area of cross section at the time of measurement of…

Q: Find: The internal forces at point C. 0.5 ft 3 ft- 2 ft A |150 lb/ft 8 ft 4 ft -

A: We have to determine the value of internal force at point C in the given beam as per the given data…

Q: -30 ft- ft OE 60 k 40 k - 30 k -30 ft- OF 20 ft impi snossib

A:

Q: RA, Ri , Vo, VB, Vc MA, MB, Mo.

A: Since given beam is determinate therefore ILD will consist of straight lines

Q: 3. For the system forces shown, solve the following: (the coordinates are distance in meters from…

A: Given  Forces F1 , F2 , F3 , F4 and their coordinates ..     Clockwise moments = negative…

Q: 2- Find the value of F, if P=360N, a=15°, B=30°, and the resultant is acting along the х-аxis. Y F P…

A: Solution; Given that; P=360N α=15°β=30°Find;F=?

Q: (A) mum mmmm (C) mm (D) mmm mim Which of the following most nearly the degree of static…

A:

Q: y 400 N 3 2 30° 1 300 N 1 X 700 N

A:

Q: solve by ues method of joint

A: ##Calculation of member forces  of truss using Method of joints###

Q: 10t 5t to B A 60° 60 4 cm C 4 cm С 4

A:

Q: M M M 13.9kft СЕ 4.64 kips M 9º MB 30 kips KN KN E E ·6² 6². 17.97kips 40kips E kNm kNm kNm 4…

A: Given data:- Below diagram is given in question;

Q: 3 A bar of 30 mm diameter is subjected to a pull of 60 kN. The measured extension on gauge length of…

A: 8. Given:- P=60kN L=200mm change in length =0.09mm To find:- poisson's ratio and threee modulus of…

Q: find dy/dx for the flowing * y = secʻx – tan" x

A: Let's first simplified the given function so, that its differentiation will be easy

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.