Rebound Non- UPV Surface Selection of Hammer destructive Calibration Condition Test Surface Test testing Must be smooth, dry, and free of honeycombing Correction factor 1.0 set Affected by the depth of carbonation Troweled surfaces generally exhibit higher rebound numbers than screeded or formed finishes Does not destroying the integrity of the structures

Rebound Non- UPV Surface Selection of Hammer destructive Calibration Condition Test Surface Test testing Must be smooth, dry, and free of honeycombing Correction factor 1.0 set Affected by the depth of carbonation Troweled surfaces generally exhibit higher rebound numbers than screeded or formed finishes Does not destroying the integrity of the structures

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7) Compression controlled failure in reinforced concrete beams happen when the concrete in compression "crushes" after the steel in tesions has reached the point of yielding. True False
9) Suppose in the high temperature DSR test in the RTFO-aged condition, the measured G* was 2.2 kPa, while the rutting parameter was 2.1 kPa. Answer the following: a. Does the tested binder meet the SPV criteria for RTFO binder in the DSR rutting test? b. Although not mentioned here, back-calculate and report the phase angle.
In the solution with the same concentration, strength loss of the hardened cement paste soaked in magnesium sulfate solution was less than that in sodium sulfate solution. why?
In a reinforced concrete element, how many times greater than the instantaneous elastic deformation can be thelong-term deformation?
Impact test measures (a) Hardness (c) toughness ......... of material. (b) ductility (d) brittleness
QUESTION 1 (a) List the 10 minerals in the Moh’s hardness scale, from the softest one to the hardest one. (b) According to the definition of minerals, point out which one is a mineral among the following ones (quartz, water, ice, coal, petroleum). (c) Indicate the differences between color and streak, using magnetite, hematite and limonite as examples. (d) State the difference between cleavage and fracture of minerals, using quartz and mica as examples. QUESTION 2 (a) What is the theory of plate tectonics? (b) State the two (2) types of plates and three (3) types of boundaries. (c) How many percent do sedimentary rocks take in the crust (volume) and in the continents area? (d) What are major mineral components in sedimentary rocks? QUESTION 3 (a) Define the following terms with sketches where appropriate: i) Rock deformation ii) Strike iii) Dip iv) Dip angle (b) What is the difference between normal and reverse faults? Show diagrams
consists of particles which vary in size between (2 - 0.06) mm and it is mainly consists of Quartz with small percentages of other minerals. اخترأحد الخيارات a. Sand b. Gravel C. Silt CLEAR MY CHOICE
Explain how 27Al NMR is useful for studying cement hydration.
Using the AASHTO T 283 test, three HMA specimens were freeze-thaw conditioned and three were unconditioned. All the specimens had a diameter of 150 mm. Table P9.40 shows the thickness and load at failure of each speci- men. Determine: a. The tensile strength of each specimen in MPa. b. The average tensile strength of the conditioned and unconditioned specimens. c. The tensile strength ratio (TSR). d. Does the mix pass the Superpave criteria for moisture susceptibility? TABLE P9.40 Unconditioned Specimens Conditioned Specimens Thickness, mm 64 63 63 63 64 62 Load at failure, kN 11.5 10.5 10.8 9.0 9.5 9.2
(b)Rupture stress: ___________________________(c)Secant modulus at stress level of 420 MPa: _____________ (d)Tangent modulus at stress level of 420 MPa: _____________(e)Determine the plastic strain at stress level of 420 MPa: _____________________________(f)If the shear modulus of the material is 55GPa, determine thePoisson’s ratio assuming the material is isotropic._____________________________(g)Determine the axial force acting on the specimen when it isextended by 0.2 mm
Q-5 Tie bars of 12 mm diameter are to be provided in a concrete pavement slab. The working tensile stress of the tie bars is 230 MPa, the average bond strength between a tie bar and concrete is 2 MPa, and the joint gap between the slab is 10mm. Ignoring the loss of bond and the tolerance factor, the design length of the tie bars (in mm, round off to the nearest integer) is