help pleasee 7 to 12 I READING WRONG METER MARKSADDING OR DROPPING A FULL TAPE LENGTHERRORERRORMISTAKEMISTAKEL IMPERFECT ALIGNMENT OF TAPE6 IMPERFECT ALIGNMENT OF TAPEERRORO MISTAKEERRORMISTAKE5 IMPERFECTION OF OBSERVATIONERROR* TAPE NOT STRETCH STRAIGHTMISTAKEERRORMISTAKEA ADDING A CM., USUALLY IN MEASURING THE FRACTIONAL PART OF TAPEAT THE END OF THE LINEERRORVARIATIONS IN TENSIONMISTAKEERROR9 RECORDING NUMBERS INCORRECTLY (EXAMPLE 78 IS READ AS 87)O MISTAKEERRORMISTAKE1o TAPE NOT HORIZONTALO ERRORMISTAKEI| VARIATIONS IN TEMPERATUREERRORO MISTAKEL TAPE NOT STANDARD LENGTHERRORO MISTAKE

7 - Error Tape is not stretched straight due to its weight which causes sag in the tape . This is…

READING WRONG METER MARK (ADDING OR DROPPING A FULL TAPE LENGTH O ERROR ERROR O MISTAKE MISTAKE IMPERFECT ALIGNMENT OF TAPE 6 IMPERFECT ALIGNMENT OF TAPE ERROR O MISTAKE O ERROR MISTAKE IMPERFECTION OF OBSERVATION O ERROR * TAPE NOT STRETCH STRAIGHT O MISTAKE ERROR MISTAKE ADDING A CM., USUALLY IN MEASURING THE FRACTIONAL PART OF TAPE AT THE END OF THE LINE ERROR VARIATIONS IN TENSION O MISTAKE O ERROR 4 RECORDING NUMBERS INCORRECTLY (EXAMPLE 78 IS READ AS 87) MISTAKE O ERROR O MISTAKE 16TAPE NOT HORIZONTAL O ERROR O MISTAKE | VARIATIONS IN TEMPERATURE O ERROR O MISTAKE 12 TAPE NOT STANDARD LENGTH O ERROR O MISTAKE O O

READING WRONG METER MARK (ADDING OR DROPPING A FULL TAPE LENGTH O ERROR ERROR O MISTAKE MISTAKE IMPERFECT ALIGNMENT OF TAPE 6 IMPERFECT ALIGNMENT OF TAPE ERROR O MISTAKE O ERROR MISTAKE IMPERFECTION OF OBSERVATION O ERROR * TAPE NOT STRETCH STRAIGHT O MISTAKE ERROR MISTAKE ADDING A CM., USUALLY IN MEASURING THE FRACTIONAL PART OF TAPE AT THE END OF THE LINE ERROR VARIATIONS IN TENSION O MISTAKE O ERROR 4 RECORDING NUMBERS INCORRECTLY (EXAMPLE 78 IS READ AS 87) MISTAKE O ERROR O MISTAKE 16TAPE NOT HORIZONTAL O ERROR O MISTAKE | VARIATIONS IN TEMPERATURE O ERROR O MISTAKE 12 TAPE NOT STANDARD LENGTH O ERROR O MISTAKE O O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the three projections with an illustration only for understanding
9-13.
2 m Gate 3m by 6 m Water p=1000kg/m³ 6 m .B
9-12 Locate the ibaid y of the area. 4 in. 8 in Proh. 9-17
Degree of static indetermi nacy
RCERT, CHANDRAPUR B.TECH, SEM I/II SECTION-B1 ENGINEERING GRAPHICS ASSIGNMENT NO.2: ORTHOGRAPHICS PROJECTIONS 1. Draw the following views of the object shown pictorially in fig (i) Front view, (ii) Top view. (iii) Side view from the right. CKS 118 2. Draw the following views of the object shown pictorially in fig (i) Front view. (ii) Top view. (iii) Side view from the left. 19 6 22 12 25 75 ASSIGNMENT/EG/N KADE/RCERT, CHANDRAPUR
Define One-Way Eccentric or Moment Loading
07: Water is flowing through apipe shown in Fig. what is the Difference in datum head (2₂-2₁), if the rate of flow through the pipe is (60 lit/sec). Jp Flookpo Ans: 2₂-2, -25.47m mm Datum line P₁ = 350kpa N 2
5kN 30 30 Determine the degrees of freedom O 16.667/EA O 16.766 O -16.667/EA O 0/EA O 16.667
Locate the centroid y̅ of the shaded area.
Construct the top view of triangle ABC
********** us esecale (2-2) to draw the orthographic projections (top view, [rout view, side) for the shapeshown below