‘ *9-120. When the tide water A subsides, the tide gateautomatically swings open to drain the marsh B. For thecondition of high tide shown, determine the horizontalreactions developed at the hinge C and stop block D. Thelength of the gate is 6 m and its height is 4 m. pw = 1.0 Mg/m³.A3 mBProb. 9-1202 m4 m

Given data,the length of the gate L = 6 mthe height of the gate h = 4 mthe density of the water Find…

Answered: reactions developed at the hinge C and…

Engineering

Mechanical Engineering

reactions developed at the hinge C and stop block D.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: What are the principal stresses? How can they be determined?

A: Principle stresses can be defined as the maximum or minimum normal stresses on a specific plane. The…

Q: What are the general equations of plane stress transformation?

Q: Von mises and tresca agree in pure shear

A: In machine design, mainly five failure theories are used to relate stress with the strength of…

Q: Write the General Equations of Plane-Strain Transformation?

A: The plane strain is a two-dimensional state of strain in which all the changes in the shape of the…

Q: Please write down the fundamental law of gearing

A: Gears - Gears are power transmission device, used to transmit power between two shafts. They are…

Q: While solving problems using the average normal and average shearstress equations, why is the…

A: While calculating average shear stress, theoretically, the flaws in the system are not taken into…

Q: State the formula for: - the actual mechanical advantage (AMA) of wedge; - the ideal mechanical…

Q: 6- In a sand-casting operation, a part whose side view and top view are shown below is to be made.…

Q: 2. What are the factors affecting the freezing time? Explain it in detail.

A: Air temperature, air density, air humidity and air turbulence are other factors that have to be…

Q: 2. A fluid with a shear rate of 0.5 per second, and the shearing stress 0.76 N per m². What is its…

Q: d) i. Describe distributive forces. ii. Explain 3 (three) examples of distributive forces in terms…

A: Distributed forces: It is a force which acts on a surface, not just on one place. The intensity of…

Q: Explain the difference between normal stress and shear stress?

Q: How did you determine the eutectic point? Explain.

A: In phase diagram , eutectic point is the point where liquid exist at the lower temperature.this…

Q: How can we apply the general equations of plane stress transformation?

A: An object is under a biaxial state of stress when the stress exists only inside the 2-dimensional…

Q: F. 15° 700 N

A: Draw the FBD for the given question and find the angle between both the forces.

Q: A product is to be reproduced, Provided that the weight of the solid steel shaft with a length of 1m…

Q: Define the term transverse shear?

A: The shear stress which occurs due to bending moments in a body is known as the Transverse shear.

Q: What are the units and equations for shear stress and shear strain

A: Stress: The ratio of the internal resistive shear force to the cross-sectional area of the object is…

Q: O Formability and strength of surfaces will help reduce wear. O Modulus and high melting point of…

Q: shape factor for a casting in the form of an annular cylinder

A: Given; The shape factor for a casting in the form of annular cylinder ?If outside diameter, D=25…

Q: Give example of solid bars behave as springs under the influence of a force.

A: It is known that the spring constant for spring is equal to the force applied to a spring and…

Q: Give an example of the Absolute Maximum Shear Strain?

Q: Determine angle of repose for the given powder sample having the height of the powder pile=5inches…

A: Given data: h=5 inr=d2=13 in

Q: What is the relationship between moment and shear?

A: The shear force and bending moment are related to each other through a differential equation. The…

Q: How can we calculate the maximum stress?

A: Stress: Stress is defined as the developed force in the specimen per unit area when that specimen is…

Q: Can reduce the by reducing rate of production when using break- even point. (a) Selling price (b)…

A: following is the answer to the above question-

Q: Explain the Comparison of temperature scales, and show in digram?

A: Generally, we have three temperature scales Fahrenheit temperature scale. Celsius temperature scale.…

Q: 5 examples of practical engineering applications of Mohr's

A: given: Provide any 5 examples of practical engineering applications of Mohr's Circle

Q: A spherical drop of molten metal of mm was found to solidify in 10 s. A drop of radius 8 mm would…

A: Given:Radius of molten metal, r1=2 mmSolidification time, t1=10 sRadius of molten metal, r2=8 mm

Q: asting is made of an annular cylinder of outside diameter 30 cm, inside diameter 20 cm , height 30…

A: Given:A cylinder of outside diameter 30 cm, inside diameter 20 cmand height 30 cm

Q: B21 Show that a; the work done in isothermally creating unit surface area of a liquid, is equal to…

A: Surface tension -Surface tension is the surface energy per unit area , due to unbalanced cohesive…

Q: casting (b) Investm

A: given: For casting of turbine blades made of high temp and high strength alloys, the most suitable…

Q: Can the External forces be applied to a body as distributed or concentrated loadings?

A: Yes, external forces can be distributed or concentrated.

Q: Discuss the external force and internal forces of this structure.

Q: Define the normal stress, shear stress, normal strain, shear strain, elastic modulus, Poisson's…

Q: - In a rolling process, the state of stress of the material undergoing deformation is (a) pure…

A: In a rolling process, the state of stress of the material undergoing deformation is Answer: (c)…

Q: For the case of a perfectly plastic

A: Given: The maximum reduction in cross-sectional area per pass (R) of a cold wire drawing process is:…

Q: How can we find the value of shear flow?

A: Shear flow: In the built-up beams, the phenomena of shear flow appear frequently. These beams are…

Q: Illustrate the effect caused by the longitudinal shear stress?

A: In addition to transverse shear stresses the beam also experiences longitudinal shear stress under…

Q: Can the Shear stres also occur during axial loading?

Question

‘

*9-120. When the tide water A subsides, the tide gate
automatically swings open to drain the marsh B. For the
condition of high tide shown, determine the horizontal
reactions developed at the hinge C and stop block D. The
length of the gate is 6 m and its height is 4 m. pw = 1.0 Mg/m³.
A
3 m
B
Prob. 9-120
2 m
4 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data and find out

VIEW

Step 2: Finding the pressure at the side A and B

VIEW

Step 3: Finding the force excreted on the side A and B

VIEW

Step 4: Finding the horizontal reaction at point C and D

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

- Sketch the principle of a hydraulic press. Explain the principle of the amplification of the force. - When the primary piston is moving for Ax, what is the distance the secondary piston Ax will move?
I need the answer as soon as possible
i need the answer quickly
What is the difference between direct and shear stress?
What are the fundamental problems in Shear stress?
Why the first two statements are correct? That is: (1) Why the deflection of a shaft is primarily controlled by geometry, not by material? (2) Why the stress in a shaft is controlled only by geometry, not by material?
Give an example of Shear Flow in Built-Up Members?