Q3: Ethyl ether is made by dehydration of ethyl alcohol in the presence of sulfuric acidat 140 °C2C₂H5OH→→C4H₁0O+H₂OA simplified process is shown in figure below. If 87% conversion of the alcohol fed toreactor occurs per pass stream in reactor.1- Write the equations that simulate above process.2- Perform the degree of freedom for the overall and sub processes (List your answerin table).Pure ethyl ether (1200 kg/hr)93% H₂SO47% H₂OAlcoholseparationDiluteH₂SO4 solutionFresh feed95% alcohol5% waterReactorEiherseparationRecycle92% dcahol8% waterWasteSulfuric acidand water

Answered: re below. If 87% convers tor. te above…

Engineering

Mechanical Engineering

re below. If 87% convers tor. te above process. for the overall and sub

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Completely solve and provide the diagram. Box the final answer. Write legibly 4. A single effect water evaporator operating at 125 kPa abs vapor pressure. Motive steam is available for evaporation at 1.0 MPa with 90% vapor content, what is the mean temperature difference?
Problem 2 An Air Force Research Lab engineer is asked to evaluate the maximum theoretical work that could be produced by the first stage turbine section of an experimental jet engine. Test stand measurements provide the following information: a. Entering air conditions: 1400 K, 8 bar b. Exiting air conditions: .8 bar Part 1: Since you don't have a mass flow rate measurement, what will be the units will you report maximum theoretical work in? Part 2: Write the first law equation for your control volume showing all terms. What assumptions will you make to simplify the equation. Part 3: Pin down the outlet state on a notional T-s diagram for air (just show the two isobars). Why did you select this point? Part 4: What assumption about the properties of air will you make in order to solve this problem? Part 5: Use the appropriate form of the 'Tds' equation and the air tables to solve for the exit state. Part 6: Calculate the max theoretical work
b) The high pressure units on a steam plant operate at 10bar (gauge), and the condensate is sub-cooled by 9.5K. If the mass flow rate of condensate is 10 kg/s, use the provided steam tables to determine how much saturated steam at 1.5 bar this condensate could produce. Note it is sufficiently accurate for high pressure condensate, as in this question, to assume that the specific enthalpy is the same as for the saturated liquid at the same temperature.
Consider a tank filled with ultra high purity nitrogen. The pressure gage reads 14898.7 kPa. The ambient pressure in the laboratory is 1 atm. The volume of the tank is 1 m3. You use the gas to purge analyzers and a mass flow controller is set to deliver this gas at 0.25 kg/min. How many hours can you purge your analyzers. Please list any assumptions REDMI NOTE 8 PRO AI QUAD CAMERA Activate Windows
8. The exact differential equation of enthalpy can be expressed as below: dH=-uCpdp + C₂dT where C: constant pressure heat capacity u: Joule-Thomson coefficient μl= a) Derive the exact differential equation of enthalpy from the general exact differential equation of enthalpy: = (3), dp + (7) dr T dH = b) Considering that you use nitrogen gas to make a temperature drop to an isenthalpic system, how much pressure drop is required to cool the system by 20 K? The Joule-Thomson coefficient of nitrogen is u 3 0.27 K atm¹. c) Prove that the Joule-Thomson expansion can occur without change of enthalpy (isenthalpic process).
intake valve intake compression JO BI Tuel injector the temperature of the gas; power exnaust vaive 0010 exhaust The diagrams show the cylinder of a petrol engine in 4 stages. Petrol vapour and air are drawn into the cylinder, The mixture is then squeezed together, and then exploded by a spark. The explosion pushes down the piston. The exhaust gases are then expelled from the cylinder. Use the first law of thermodynamics to analyse the energy changes during the process. At each stage explain what happens to i) the pressure of the gas; ii)
Problem 03.028 - DEPENDENT MULTIPART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you willI be unable to return to this part. A 1.9-m3 rigid tank contains steam at 220°C. One-third of the volume is in the liquid phase and the rest is in the vapor form. The properties of steam at 220°C are given as follows: vf= 0.001190 m3/kg and vg= 0.08609 m3/kg. Steam Vm3 220°C Problem 03.028.b - Quality of a saturated mixture Determine the quality of the saturated mixture. (You must provide an answer before moving to the next part) The quality of the saturated mixture is
The problem needs to be solved using probalistic design using normal distrubtion table Z
Q#4: a. briefly explain the how the crude oil is refined into petroleum products. b. Write down seven Basic Operations in Petroleum Process. c. List various Hydrocarbon in order of fractional distillation of crude oil.
Batch-5 1973: Ford Pinto : Fuel System design write about fuel lines and fuel filter in detales.
AaBbCcDd AaBbCcDd AaBbC AaBbCcC AaB AaBbCcD AaBbCcDd AaBb I Normal 1 No Spac. Heading 1 Heading 2 Title Subtitle Subtle Em. Emp- Paragraph Styles There is a hot water source in New Delhi.Our plan is to use this heat source for heating and hot water supplies of a site of 100 hostels. The outlet temperature of the water from the source is 170°C. 4- An official realizes that the outlet temperature of the groundwater is too high and is considering using it to generate electricity. Design an Organic Rankine Cycle (ORC) suitable for this purpose. (Ctrl)
4.17 In an auditorium, 17,150 students are watching slides. The MRT is 80°F and the average room air temperature is 72°F. Air enters the room at 57°F. Assume the lights are out and no heat gain or loss occurs through the walls, floor, and ceiling. (a) How much air (CFM) should be supplied to remove the sensible heat? (b) Explain what must be done to remove the latent heat.