rce is 1, 450 MPa (c) L 50 KN/m

Q: Determine the centroid of the given composite figure. The area of the geometric figures drawn in red…

A:

Q: The mass of the block that can be attached at point E so that the angle indicated (excel) is…

A: Answer In order to find the weight of the block that can be attached at point E to be adequate for…

Q: The blocks shown in the figure weighs 35 kips. Find the value of x

A: Thw weight of the block is balanced by buoyant force by oil and water.

Q: 100 90 80 70 60 50 40 30 20 10 0.5 0.05 Grain size (mm)-log scale From the graph D60 = 0.997 mm; D30…

A:

Q: For the cross section shown, the distance of the plastic neutral axis from the bottom is * 8 in 2 in…

A: Given data in question  Dimensions of unsymetrical I sections To find out  Depth  of plastic neutral…

Q: Prepare and complete the differential level notes for the information shown in the accompanying…

A:

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm.

A: Volume of 1=(40×17×38) - Volume of 2                          =(40×17×38) - 12×10×10×17…

Q: cos^2 x = cscx cosx/tanx + cotx. prove the identity.

A:

Q: Complete the table

A: To complete following table     As asked only displaying excel formulas and output

Q: GIVEN FIGURE SHOWN, DETERMINE THE LOCATION OF CENTROIDAL X AND Y. Y 4" 2 in. radius 9" 12" X- -X 2"…

A: NOTE : As per our guidelines we are supposed to answer only one question. kindly repost another…

Q: net area in tension, Ant, of the L6 x 6x 3/8 angle shown in the figure is equal to:

A:

Q: 21.42 ounces + 22⁄9 ounces

A:

Q: Problem 01: Given the figure at the right side: Determine the following a. Zx b. Sx c. shape factor…

A:

Q: Instructions: Use Dimensional Analysis & Chain conversion method. (Provide in Both) (In detail with…

A: Use Dimensional Analysis & Chain conversion method. (Provide in Both) (In detail with each…

Q: 14.6 The structural steel built-up member (b) of Problem 14.2 is to be used as a simply supported…

A: A built-up steel structural section is given. The section is simply supported with a span of 40 ft…

Q: A W12x96 is loaded as shown. Find the maximum stress at point A (mid - height of

A: Column W12x96Area = 28.2 inch2Moment of inertia about the strong axis (Ix): 983 in4 (from steel…

Q: PROBLEM The centroid of the T-section shown is 2.9 inches above the base and x is 11. What should be…

A:

Q: 2. Determine the values of &, ¢, and oMn for the sections shown below 18 in. 21 in. 3 #11 bars 3 in.…

A: Refer Appendix A, Table A.2 for bar no. 11 and cross section area of bar no.11 Area of Steel…

Q: For the objects shown on the left below with an indicated cutting plane. Circle the letter…

A: To select the correct option for the given figure with section shown on the left side.

Q: Locate the centroid of the plate area shown below: (All units are in mm). R10 O. 115 X R30 | 30

A:

Q: Where did you get the Value of A=4 and b=3?

A:

Q: Dimensions in the following diagram are in millimetres. Round answer to 2 decimal places. If EK =…

A: Two points on a curve connected by a line segment are known as a chord. Chords are lines connecting…

Q: A beam of square cross-section is bent in the plane of its diagonal. A cut is made at top and bottom…

A: A beam of square cross-section is bent in the plane of its diagonal.A cut is made at the top and…

Q: Compute the smallest net area for the plate shown below: Plate thickness = 12 mm A Bolt diameter =…

A: For calculating the smallest net area of steel plate, consider all possible sections with bolts.The…

Q: 5. Solid Mensuration. A rectangular gold has the following dimensions: 2m x 4m x 8m. Now it has been…

A:

Q: AP of five terms, the sum of the last 4 terms is 38 and the product of the 2nd and 5th is 70. Find…

A: Given:- sum of last 4 terms =38 product of 2nd and 5th =70 To find:- progression

Q: A pair of forceps used to hold a thin plastic rod firmly is shown in (Figure 1). < 1 of 1 Figure…

A: The forces at thumb and finger are FT = FF =16.5NThe distance of P from thumb and finger, d1…

Q: The 1-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

A:

Q: QUESTION 1 Complete the table below. LINE BEARING DIST (M) AB N 60° 15.3' E 40.311 BC S 64° 5.6' E…

A: To Find : Latitudes ,Departures, DPD , Double Area ( DA ) and Area for traverse. Given: LINE…

Q: Determine the moment of Area of the given Built-up section about its centroidal axis.The top flange…

A: Given I section With top Flange 8" x 1" Bottom flange 16" x 1.5" Stem(web) 16" x 1" 2 Angle sections…

Q: 50 mm A 50 mm 50 mm D, 50 mm 50 mm B

A:

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.