RC=1.4k R₁ =1ake B=100 Is=6x156A R₂ = 36k_R Assume that IE = B = (B+1) IC Ri VA = 0.95 VT = 26mV VB = 0.95V find IC, VCE and Re www Vec=5V Rc RE

Q: Convert the decimal NUMBER 19711.654785156 to octal number showing the steps (Note : The problem…

A:

Q: _is algebraic difference of the upper and lower limits of the range Span Range Precision O Accuracy

A: Span , range , precision and accuracy are common terms use in measurement.

Q: Differentiate between MCB and kit kat fuse

A: MCB : MCB stands for miniature circuit breaker it is a electrical device in such way that it…

Q: Write down the short note on Inter symbol interference.

A: In the telecommunication , Inter symbol interference is a methodology of distrotion,  in which a…

Q: Dot-matrix printers are usually print at speeds of between ________________characters per second. 10…

A: Dot-matrix printers are usually print at speeds of between ________________characters per second. A)…

Q: Convert the following Hexadecimal numbers to Decimal numbers: (AC), and (FAI

A:

Q: Electrical (VHDL) Difference between intial and always block.

A: Verilog is Hardware Description language. Verilog have different layer of abstraction. In each time…

Q: Draw the Direct Digital Control block diagram and show the Implementation of the Problem using a…

A: The block diagram of the direct digital control is shown below,

Q: The navigation and system data message is transmitted through the: a.50 Hz modulation b.The C/A…

A: Transmission of the navigation and the system data is done by using the specific method.

Q: struction is executed two data bytes from HL registers that were previously stored on the stack are…

A: In this question, we have to explain about pop instruction and flags..

Q: Choose the correct statement: a. The pitch period for male speakers is sh A b. The pitch period for…

A:

Q: Crosstalk, shielding and grounding

A: According to question: Crosstalk: It is one of problem seen in communication system which occurs…

Q: Write an Arduino based code to take input from two switches, if switch one is pressed than glow full…

A: The input is taken from two switches  On pressing switch one, the full spectrum on RGB Led.  On…

Q: Convert the decimal number 694 to BCD. Kindly put subscript in answer.

A: Brief description : In digital electronics we have different type of number systems such as,  Binary…

Q: Explain any four dynamic characteristics of measurement system.

A: The explanation is as follows.

Q: Do the following binary subtraction: 11111000 1.10111- 0 0 10 0 0101.01110 (Note : The problem…

A: Given  A =111110001.10111B =001000101.01110

Q: Evaporator in absorption cooling system changes into vapors at low pressure? O i. Refrigerant O ii.…

A: Purpose of Evaporator in absorption cooling system

Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring system

A: RTD (Resistance Temperature Detector) is an electronic device used to detect the temperature by…

Q: Why ar are digital signals more accurately reproducible than analog signals?

A: Why digital signals more accurately reproducible than analog signals?

Q: For self-excited generator, why isn't max. generation voltage generated as soon as the Armature…

A: Self-excited generators are modern DC generators with field coils area unit that start with the…

Q: Could somebody transcribe this in LEGIBLE handwriting?  Or type it?  This is the solution I need but…

A:

Q: How are electrons produced in scanning electron microscope (SEM)? What is the function of scanning…

A: Above is the figure of SEM (a) In SEM, electron beam inspects the sample in a bitmap pattern. At…

Q: Construct a 5-2-2-1 weighted code for decimal digits. What numbers does 1110 0110 represent in this…

A: To do: a) We have to construct 5-2-2-1 weighted code for decimal digits. b) what numbers does 1110…

Q: How can random error be reduced? a.Using a more accurate instrument. b.Change the measuring…

A: A random error is also called unsystematic error due to unexpected and unpredictable causes and very…

Q: Logic

A:

Q: write paragraph about how to concat and installation circuit breaker with socket ,what is…

A: Aim-  To write paragraph about how to connect and installation circuit breaker with socket.

Q: D(s) Ks R(s) C(s) (5 K)s- (2 L)s (3 M)s C(s) =? (20P) K: Okul numaranızdaki rakamların toplamıdır…

A: Given control system shown

Q: Convert the octal NUMBER 7135. 2235 to hexadecimal number showing the steps (Note: The problem…

A: NOTE: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: is a Fragile type temperature sensor

A: Resistance thermometers employing metallic conductors for temperature measurement are called…

Q: The information signal is always an analog signal. an analog signal in case of an analog carrier…

A: A signal can be in form of analog or digital signal.

Q: Add the following BINARY NUMBERS 111000001+ 110010110 (Unused boxes in the answer must be filled…

A: In this question we will perform binary addition...

Q: B- What is the noise in communication sytems. Clasify the types of noise and how can elimiteate the…

A: we need to discuss what is the noise in communication system and  types of noise and how can we…

Q: Which frequency band is the standard FM radio broadcast? O SHF O VHF O MF UHF O UHF

A: SHF : ( Super High Frequency ) : It's frequency band is 3 GHz to 30 GHz. VHF : ( Very High Frequency…

Q: Explain with a neat block diagram the measurement of displacement using RTD (measuring System)

A:

Q: (a) Perform the following conversions (show all workings). (i) (ii) E1D5.C4₁6 to Decimal number…

A: Decimal0123456789101112131415Hexadecimal0123456789ABCDEFHexadecimal to decimal :-(E1D5.C4)₁₆ = (14 ×…

Q: The colour of NC push button is green. Select one: O True O False

A: Here NC stand for Normally Closed . NC push button are make electrical contact with the circuit when…

Q: Write a program that adds 5 bytes of data and save the result. The data should be following hex…

A: The given data is, DATA DB 25H,12H,15H,1FH,2BH    The required code is shown in the next step as,