RC R1 Vc Q1 R2 RE Calculate the optimum value for R1 such that the transistor is biased at 1/2(V1). V1 = 15Volts, IcQ = 1mA, RE = 1500ohms, VBE = 0.6, %3D !3! %3D %3D HFE = 176 %3D Enter your value for R1 and choose the unit.

Q: A front of a building 50 m by 16 m is to be illuminated by sixteen 1000-W lamps arranged so that…

A: The solution can be achieved as follows.

Q: A 30 60-Hz induction motor runs at 715 rpm at no load and at 670 rpm at full load. The slip-torque…

A:

Q: explain in detail aplease

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Consider the circuit below. At t= 0 the switch is opened. Find the inductor current, i(t), for t> 0.…

A: The solution is given below

Q: Suggest an alternative circuit by which FM signal can be detected

A: The FM signal can be detected by the basic Foster-Seeley circuit shown below:

Q: 1. The current / in the circuit of Fig. 2.63 is: ww 3V 10 V ww 2. (a) Calculate current i in Fig.…

A:

Q: In an area of 3 m² there are 12 field lines each representing of 1 Wb. What is the flux density?…

A: Given Data Total field lines = 12 The flux per field lines = 1 Wb Area = 3 m2

Q: Three wires are parallel and carry constant currents as shown below. What is the net magnetic force…

A: In the question, currents are flowing in 3 parallel wires as shown in the figure.  Find the force on…

Q: Find the equivalent resistance across terminals A-B Write your answer with detailed calculations in…

A: We will convert given star to delta then we will find out equivalent resistance.

Q: Activity no. 25 Compute the power absorbed or supplied by each component of the circuit. Prove your…

A:

Q: Two identical coils with self-inductance of 250 micro-henry each are connected in series. When…

A: The two coils have inductance of 250 μH. And we know when the the two coils are connected in series…

Q: 5.WHAT IS THE CURRENT AND THE VOLTAGE IN THE FOLLOWING CIRCUIT? (VALUE 10% POINTS) | = %3D V =…

A: The power absorbed by the resistor (P) in terms of voltage and current is given by: Where, The…

Q: When the FM signal is derived in the analysis, single tone modulation is used. Comment on the FM…

A: According tot he question, we need to derive the expression for single tone FM.

Q: Activity: TF of Electromechanical Systems OL(s) Ea(s)' shown. The torque-speed curve is given by Tm…

A:

Q: Clock Construct the State Transition Diagram for the following circuit. Please include all steps. 1…

A: Given

Q: 4. Four equal resistances are connected in parallel across a certain supply producing P power. How…

A:

Q: QUESTION 13 Three capacitors, a 10 micro-F, a 15 micro-F and a 32 micro-F, are connected in…

A: (13) if capacitor are connected in parallel theequivalent capacitance Cth = C1+C2+C3 Cth=10+15+32 uF…

Q: 2. A 500W, 100kHz carrier is modulated to a depth of 60% by modulating frequency of 1kHz. Calculate…

A: In this question we will find total power transmitted in AM wave and sideband components of AM…

Q: Find the output voltage v, (t) for the circuit shown in Figure 1. 42 6 H 2H v(1)= 24cos(4r+140) -> 4…

A: Given circuit shown

Q: Using superposition find the voltage V, in the network shown in Figure I. 50 240 V 1.3 20 0 84 V 16…

A: While using the superposition theorem, we take 1 source at a time by deactivating the other sources.…

Q: c) v(t) = 300 sin 500t = %3D

A: According to the question we have to convert in cos form.

Q: 3. Solve the equivalent resistance across: a. "a" and "b" b. "c" and "d" 20 KAMA 20

A:

Q: QUESTION 12 In an RL parallel circuit, ET = 120 V, R = 15 ohms, and X L= 20 ohms. What is the power…

A: Answer 12:  Given that R= 15 ohm XL= 20 ohm

Q: The op amp in the inverting amplifier circuit has the following typical parameters: AOL = 2 x 104,…

A:

Q: Multiple Choice A 50 and 100 uF capacitors are connected in series and across a 100 sin(wt+30)…

A: In this question we need to choose a correct option.  For pure capacitive circuit current lead…

Q: The transfer function of a system is 2s² + 6s +5 (s + 1)² (s+2) The characteristic equation of the…

A: The characteristics equation is denominator of transfer function. It is always denoted as 1+GH=0.…

Q: The output of a D latch shown below will not change if D EN EN D is HIGH D is LOW the output is LOW…

A: The digital circuits can be combinational as well as sequential circuits. The combinational circuits…

Q: (i) Describe the working of a single-phase series inverter with appropriate circuit and waveforms…

A: "Since you have posted a question with multiple questions, we will provide the solution only to the…

Q: For a given LTI system with frequency response as H(w)=3, 0<w<11 If the input is:…

A:

Q: Calculate the node voltages in Fig. 9. show the value of each node voltages. - 8A - 3A 3'u 4U 20…

A:

Q: 3. Boron is implanted into an n-type silicon wafer to a depth (i.e., range) of 0.3 um. It is known…

A:

Q: Q6.C. A transistor with a maximum junction temperature of 120 C° has a junction to the base thermal…

A: Given parameters Junction temperature =Tj =1200 C Ambient temperature=Ta =500 C Average power…

Q: A room is to be illuminated with the help of 12 lamps of 200 watts rating each giving an output of…

A: Introduction: Luminous Flux: It is defined as the total amount of light energy per second of a…

Q: The amplifier circuit to be used is the one shown in Figure 1. Size the components to obtain a gain…

A: The ac circuit is given as Now the small signal modeling of the amplifier will be

Q: Assume the output is initially HIGH on a leading edge triggered J-K flip flop. For the inputs shown,…

A: According to the question we have to discuss about the pulse on which output go from high to low.

Q: Find the value of I required to establish a magnetic flux of Ø = 0.75 x 10-4 Wb in the series…

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.