Please solve both in 1 hour please 14The average air temperature and relative humidity at UCR on Monday, January 15, 2021 was 25.0°C and 25%, respectively. Calculate the corresponding dewpoint temperaturein °C.A. 2 °CВ.5 °СC. 8 °CD. 10 °CE. 12 °CF. 14 °C15The diameter of a snow tube sampler is 7.5 cm. The depth of the snow in the tube is 100 cm. The mass of the snow is 795 g. Calculate the % H2O content of the snow (by volume),A. 5%В. 8%C. 13%

The solution is given below: . As per our company policy we are supposed to answer only first part…

rature and relative humidity at UCR on Monday, January 15, 2021 was 25.0°C and 25%, respectively. Calculate the corresponding dewpoint tempera A. 2 °C B. 5 °C C.8 °C D. 10 °C E. 12 °C F. 14 °C ameter of a snow tube sampler is 7.5 cm. The depth of the snow in the tube is 100 cm. The mass of the snow is 795 g. Calculate the % H20 content of the snow (by vol A. 5% B. 8% C. 13%

rature and relative humidity at UCR on Monday, January 15, 2021 was 25.0°C and 25%, respectively. Calculate the corresponding dewpoint tempera A. 2 °C B. 5 °C C.8 °C D. 10 °C E. 12 °C F. 14 °C ameter of a snow tube sampler is 7.5 cm. The depth of the snow in the tube is 100 cm. The mass of the snow is 795 g. Calculate the % H20 content of the snow (by vol A. 5% B. 8% C. 13%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve carefully , Important.
Draw a circular hole of 2cm deep and give dimensions to it.
ıf u solve this Can u solve full please Define the following: Mechanical properties of materials: Strength of material: Ultimate strength: Yield strength: Ductility: Toughness: ıf u solve this Can u solve full please
PLS SHOW COMPLETE SOLUTION. SOLVE IT BY HANDWRITTEN. ANSWERS SHOULD BE ROUND OFF TO FOUR SIGNIFICANT FIGURES.
Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke length of 400 mm. What is the engine capacity in litres? Give your answer to 2 decimal places.
I will rate helpful. Thank you.
A hole is to be drilled as shown by the circle. Using the part geometry shown below, indicate on the part sketch where locator(s) should be positioned according to the 3-2-1 principle. Use dashed lines to indicate locators on hidden surfaces. Also indicate where clamping force(s) should be applied using arrows. Use the minimum number of clamping forces.
you solved it with a total distance of 8, not 10 like the question said. please resolve with a distance of 10
Please solve for 4.139 thx
Please answer immediately thank youuuu
Show the complete solution and use whole decimal places in solving.
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 rad/s^2, 100 kN) For stresses, type (C) for compression and (T) for tension one space after the unit. (ex: 18.19 MPa (C), 6.88 psi (T))