ramp. The rope A crate of mass m = 12.4 kg is pulled by a massless rope up a 36.9° passes over an ideal pulley and is attached to a hanging crate of mass m2 = 16.3 kg. The crates move 1.70 m, starting from rest. If the frictional force on the sliding crate has magnitude 21.8 N and the tension in the rope is 121.5 N, find the total work done on the sliding crate. m1 m2 J. The total work done on the sliding crate is

ramp. The rope A crate of mass m = 12.4 kg is pulled by a massless rope up a 36.9° passes over an ideal pulley and is attached to a hanging crate of mass m2 = 16.3 kg. The crates move 1.70 m, starting from rest. If the frictional force on the sliding crate has magnitude 21.8 N and the tension in the rope is 121.5 N, find the total work done on the sliding crate. m1 m2 J. The total work done on the sliding crate is

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A crate of mass 12.0 kg is pushed up a rough incline with an initial speed of 2.5 m/s the pushing force is 150 N parallel to the incline, which makes an angle of 25° with the horizontal. The coefficient of kinetic friction is 0.4, and the crate is pushed 4.0 m. a) What is the acceleration of the box? b) How much work is done by the frictional force on the crate? c) What is the speed of the crate after being pulled 4.0 m?
2. A cart is pulled a distance D on a flat, horizontal surface by a constant force F that actsat an angle θ with the horizontal direction. The other forces on the object during thistime are gravity (Fw), normal forces (FN1) and (FN2), and rolling frictions Fr1 and Fr2,as shown below. What is the work done by each force?
In this problem use g = 10m/s^2. The weight of the object is W = mg. 1)Find the work done on the object by the force F. 2) Find the magnitude of the normal force between the object and the floor. Answer in Newton. 3)Find the work done on the object by friction. 4)Find the final kinetic energy of the object. Answer in Joule.
A constant 112.-N force acts on a 3.81-kg box. The box initially is moving at 24.9 m/s in the direction of the force, and 3.72 s later the box is moving at 71.1 m/s. Determine the work (in J) done by this force. You may assume that the box experiences constant acceleration, but do not assume that only one force acts on the box.
9. A man pushes an 80-N crate up a frictionless slope that makes an angle of 30° with the horizontal. The man was able to push it to a distance of 5.0Om along the slope with a force parallel also to the slope. However the speed of the crate decreases at a rate of 1.5 m/s?. The work being done by the man is: A. -200 J В. 61J С. 140 J D. 200 J 14. A 6.0-kg block is released from rest 80 m above the ground. When it has fallen 60 m its kinetic energy is approximately: A. 4800 J В. 3500J C. 1200 J D. 120 J
A box has a mass of 15.4 kg is sliding along a floor with a velocity of 2.45 m/s East. A rope is attached to the box as shown producing a force of 76.3 N @ 34.3° above East. The work done by friction is found to be -776.J. What is the final speed of the box after it has been pulled a distance of 11.7 m? Select one: 14.2 m/s 0.00 m/s 0.877 m/s O d. 2.45 m/s a. b. C. m I 0 P d m 0 P
A car (m = 1.39 x 103 kg) accelerates uniformly from 3.75 to 18.5 m/s in 7.50 sec. Assume that a single horizontal force accelerates the vehicle. a) Determine the work done by this force on the car. b) Determine the average power required to accelerate the car.
A 10.0-kg particle, starting at point A at a height of 5.00 m above the ground with an initial velocity of 8.00 m/s, is moving down the curved runway. Upon leaving the runway, the particle shoots straight upwards to a height of 7.00 m above the ground before falling back down. What is the work done by nonconservative forces on the ball?
questions B, C and D please
Starting from rest, a 6.2-kg block slides 3.2 m down a rough 37-degree incline. The coefficient of kinetic friction between the block and the incline is μk = 0.55. a) Determine the work done by the friction force between block and incline. b) Determine the work done by the normal force. c) Determine the net work done on the block.
A lunch plate has a mass of 590g. It is pushed 90.0cm along a dining table by a constant force of F= 3.60N directed at an angle of 26.0 degrees below the horizontal, as shown in the picture below. If the coefficient of kinetic friction between the plate and the table's surface is 0.440, figure out; a. the normal force exerted on the plate by the table. b. the work done by the applied force F. c. the work done by the force of kinetic friction. F 90 cm
A 3.54 kg object has three forces that act on it as it moves 5.35 m in the negative x-direction, starting from rest. The three forces that act on the object are described in the table below: Force Force 19.91 N Force 2 34.7 N Force 3 49.5 N |magnitude direction |along the positive x-axis |along the negative y-axis |44.5 degrees above the -x-axis a. Determine the work done by each of the forces. i. Work done by Force 1 ii. Work done by Force 2 iii. Work done by Force 3 J J J b. What is the net work acting on the object? J c. Using work and kinetic energy ideas (Unit 7), what is the speed of the object after it has moved 5.35 m? m/s