R9-7. The rigid link is supported by a pin at A and two A-36 steel wires, each having an unstretched length of 300 mm and cross-sectional area of Z8 mm. Determine the force developed in the wires when the link supports the vertical load of 1.75 kN. -300 mm- 125 mim 100 -150 mm 1.75 kN

Q: Determine the forces in members BE, BD and CD if the weight W = 200 N. Use the sign -if the force is…

A:

Q: zirconium alloy. If an axial load of 4 kip is to be supported by the member, determine its required…

A:

Q: Determine the force in member BE of the loaded truss. Th

A: Given: TO determine: Force i n member BE

Q: B 4a E M A L AM = 10a 8a D L

A:

Q: 4-59. The post is made from 6061-T6 aluminum and has a diameter of 50 mm. It is fixed supported at A…

A: The data given is,Load, P = 50 kNModulus of elasticity, The diameter of the rod, d = 50 mmTo…

Q: A member (AC) is supported by a pin at A and a roller at B. The horizontal component of reaction at…

A:

Q: The truss is composed of equilateral triangles of side a = 2.4 m. The load is L = 370 N. Determine…

A: Given data: Side length of triangle (a) = 2.4 m Magnitude of the load (L) = 370 N Concept: At…

Q: The pyramidal truss section BCDEF is symmetric about the vertical x-z plane as shown. Cables AE, AF,…

A: Given data: load is 3.3 KN

Q: Determine the force in member CG. The force is positive if in tension, negative if in compression.…

A: Introduction In this issue, we will use the section technique to determine the force in the member…

Q: Using the Method of Sections, determine the force in members BD and CD of the truss shown below. You…

A:

Q: Determine the vertical displacement of joint C of the truss loaded with P=30 kN. The members of the…

A: A truss is defined as a structure consisting of only two force members, which together work to form…

Q: The ABC lever is supported at point A and connected to a short connection BD as shown in Fig.5-22a.…

A: Draw the free-body diagram of the lever ABC :

Q: The crate has a weight of W-350 b and the coefficient of static friction between the crate and the…

A: The friction force on the ground is 141.42 lb.

Q: A 6061-T6 aluminum alloy solid circular rod of length 4 m is pinned at one end while fixed at the…

A: Given data: The length of the rod is L=4 m. The axial load on the truss is P=15 kN. The factor of…

Q: Determine the horizontal and vertical components of force which the pin at B exerts on member BC of…

A: The free body diagram of the beam is as follows:

Q: The magnitude if the moment induced by the load about the Line-EF is The magnitude if the moment…

A:

Q: Determine the force in the hydraulic cylinder EF and AD in order to hold the shovel in the position…

A: The mass is

Q: Members AC and AB support the 150-lb crate. Determine the tensile force developed in member (AB).

A:

Q: Axial loads are applied to the compound rod that is composed of an Aluminum segment rigidly…

A: Given:As=400 mm2Aa=500 mm2Ab=300 mm2P=12 kN

Q: The 2014 T6 aluminum strut is foced between the two walls at A andB. It has a 2 in. by 2 in. square…

A: Given data T1 = 22 lb-ft T2 = 42 lb-ft Area of cross section = 2 in X 2 in

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given data, Let RA and RE are the reactions at A and E

Q: 12. The load in the bucket is 2300 N with its center of gravity at G. Determine the forces in the…

A:

Q: The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is…

A: Given : T1 = 3.3 kN θ = 39o

Q: Determine the vertical displacement of joint C of the steel truss shown inFig. a. The…

A: Answer : Given dimensions cross-sectional area of each member is A = 400 mm2 and Est = 200 GPa.

Q: |P - 60 kN B | A = πε

A: Given

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A:

Q: Each of the two members is made from 6061-T6 aluminum and has a square cross section 1 in. * 1 in.…

A: Given data as per the question Force exerts on each member=50 lb Assume The yield strength for the…

Q: Problem 2: The hanger consists of three 2014-T6 aluminum alloy rods, rigid beams AC and BD, and a…

A:

Q: Problem 3 Replace the loading on the frame by a single resultant force. Specify where its line of…

A:

Q: Each member of the truss has a cross-sectional area of 1850 mm2 and is made of A-36 steel (E=233…

A: From right angled triangle AED, i) length of member AD isii) angle  isSimilarly from right angled…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: The boom supports the two vertical loads. Neglect the size of the collars at D and B and the…

A:

Q: Q3/ Ir the allowable bearing stress for the material under the supports at A and B is opallow 2MPA ,…

A:

Q: 2. The wall crane supports a horizontal and vertical compo D. Also, what is the force in ABC has a…

A: The force equilibrium at point E is-

Q: Determine the force on each element of the reinforcement and determine if the elements are in…

A:

Q: The door has a weight of 90 lb. Its center of gravity is shown in the figure by point G. If the…

A: Draw the FBD for the given question.

Q: Bar ABD and bar CEF are connected using a pin at point C and a strut member BE to support 9000 N…

A:

Q: Determine the force in member DI of the loaded truss. Enter a positive number if in tension,…

A: Given data

Q: 16-6. Determine the support reactions at pins and 3. Take E = 200 GPa, I = 350(10) mm, A = 15(10³)…

A: Determine the support reactions at pins 1 and 2. Take E 200 GPa, I = 350(106 ) mm4 , A = 15(103 )…

Q: Members AC and AB support the 500-lb crate. Determine the tensile force developed in member (AB). -3…

A: Solution:  The step by step is shown below.  Whenever we see three concurrent forces, we go for…

Q: A B D P IT ac 000 C

A:

Q: For the below assembly, if the gap between C and the rigid wall at D is initially 0.1 mm, determine…

A:

Q: Bar ABD and bar CEF are connected using a pin at point C and a strut member BE to support a 9000 N…

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A: