R4-5. Replace the force and couple system by an P. equivalent force and couple moment at point

Q: PROVIDE DIFFERENT ACCESSORIES IN SHAPER MACHINE WORKS VERTICAL AND HORIZONTAL WITH PICTURE

A: Shaper machine is a cutting machine that converts reciprocating motion of a flywheel into linear…

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: advantages and 5 disadvantages of using trash pumpp

A:

Q: Find reaction at A.

A:

Q: Q2.Write Types of Key and Explain in detail with Diagram.

A: key A key is a machine element which is used in between shaft and hub or Boss of the pulley to…

Q: A workpiece turning at 20 rad/sec has a diameter of 4 inches. Find the peripheral speed of the…

A: Given:Angular speed of the work piece, ω=20 rad/sDiameter of the workpiece, d=4 in

Q: e

A: given:RPM N=2000time of injetion =0.0015

Q: 37. The operation of removing material with a multi-teeth circular cutter from the surface of a…

A: Drilling- It is a cutting (material removal ) process in which drill bit which is a rotary cutting…

Q: Homework 6 -Problem I – As for the symbols of the work and haet, when is the work positive and when…

A: Solving problem I If want other problems to be solved pls repost the question with a specified…

Q: Which therbligs correspond to which activities? 1.Lift and move wrench toward screw 2.Reposition…

A: Solution:

Q: also why is Q/T0 being subtracted in sgen1 while other 2 its being added

A:

Q: Draw the Ts diagram of the whole process

A:

Q: Can the rudder be manually trimmed with the autopilot engaged?* O yes No The figure below is not…

A: The rudder controls movement of the aircraft about its vertical axis .Rudder trim is done to keep…

Q: Please Give explanation in Handwritten format No COPY PASTE PLEASE 1. Inertial Forces and Couple 2.…

A:

Q: Need help on all questions. Please include all units, steps to the problem and information such as…

A:

Q: If a wrench is unable to loosen a wheel nut, what are two ways that you could increase the torque…

A: There are two ways to increase the Torque if a unable to loose the wheel nut

Q: for velocity one find the total gear ratio and not velocity

A: the output speed is:Here negative sign is just indicating the opposite direction of the rotations of…

Q: Explain the diagrame! C. Ca

A: Solution:   In the diagram, Cm is the Moment Coefficient. CL is the Lift Coefficient.

Q: a) The maximum force P that can be applied to the system based solely on the boards is most nearly…

A:

Q: shoudnt the bike and rider mass be 350 not 300?

A: Yes, the bike and rider mass must be 350 kg not 300 kg

Q: Reheat cycle then solve for it

A: given; Reheat cycle then solve for it

Q: please explain for c) what is Sum of M at hinge

A:

Q: Find out degree of freedom? show number of link and joint

A:

Q: Find the natural constraints for the turning crank shown below. CÂ cŷ

A: to find:the number of natural constraints.given:the figure

Q: Read through the following chronological instructions. Choose the correct figure that best matches…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Draw the free-body diagram for the boom. Connection at A is a pin. Draw the vectors starting at the…

A: To draw: Free body diagram of the boom. Given: The connection at A is pin. Sketch: The force In wire…

Q: 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces.…

A: When a body is immersed in water , the following forces acts on the body  1) Weight of the body  2)…

Q: The impending motion is applied when the body is Select one: O a. Just stopped Ob. Stopped Oc. Just…

A:

Q: I need the computation how the force required to engage the clutch is 428 lb. Thanks

A:

Q: Q// Drow the 5.8.0 and B,m.D yougN

A: The shear force diagram for the beam is

Q: how to calcuate moment for ridig body

A: The moment or torque of a force about a point or an axis is a measure of the tendency of rotation.

Q: A centrifugal pump rotates at 1500 revolutions per minute to transport water with a bulk velocity of…

A: A Centrifugal pump is a machine that can transfer fluid from one location to other with the help of…

Q: differentiate between caption and turret lathe

A: Capstan and Turret lathe is one of the broad classifications of a Lathe

Q: FIND THE DEGREES OF FLEDOM OF THE MECHANSNE.

A:

Q: Get the degree of freedom of the following mechanism. Pin in Siot

A: Degree of freedom for the following mechanism

Q: a-) What is konck? Describe the Knock mechanism formed in the cylinder by drawing a figure. What is…

A: Knocking is the phenomena commonly occurring in a CI engine. You may know that in a CI engine the…

Q: What is the mechanical advantage of an input piston with a diameter of 1.25" pushing fluid to move…

A: Diameter of input pushing piston, d1= 1.25" Diameter of output pushed piston, d2= 2"   To find:…

Q: The punching machine is using the flywheel for its smooth running operation. The flywheel running at…

A: Given data: Convert the “rps” into “rpm” as follows:

Q: Alm that He Cafle

A:

Q: Create your own 2 problems about couple forces with complete solution

A: Given Couple forces To find 2 Problem with solution

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.