R2 VCC 24V R1 2600 MP SA06 Vin -OV Fig.1 Transistor Switch Procedure: 1. Determine the value of base bias resistor of a transistor switch that will drive a DC motor represented by a 600 resistor R1. The motor has a rated working voltage of 24 v and will be driven by MPSA05 an NPN transistor. The control signal of Ov and 5v will come from an Arduino developmental board.

R2 VCC 24V R1 2600 MP SA06 Vin -OV Fig.1 Transistor Switch Procedure: 1. Determine the value of base bias resistor of a transistor switch that will drive a DC motor represented by a 600 resistor R1. The motor has a rated working voltage of 24 v and will be driven by MPSA05 an NPN transistor. The control signal of Ov and 5v will come from an Arduino developmental board.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-phase half wave controlled AC to DC converter is supplied from a 250V, supply. Assume the thyristor voltage drop to be 1.6V and the load current to be continuous. Evaluate the mean output voltage when firing angle is varied at 45(degree) , 60(degree) and 90(degree)
-4) Design a circait containing a comparater with a hy steresis loop a. Draw the circuit with all values of the components required for the dksign. b. What is the name of the circuit in (a). c. Sketch the output waveform when the input is a 15-V peak sine wave. d. Adjust the value of RI in the circuit such that the hysteresis width will be 10.
Q5 (a) A centre tapped rectifier has the following parameters: Nsec = 0.2, Vp(pri) = 240 V, f = 120 Hz Npri Determine the ideal average voltage (Vpc), peak inverse voltage (PIV), rms ripple voltage (Vr(rms)) and ripple percentage (r) of this rectifier circuit.
If a sinusoidal voltage is applied to the base of a biased npn transistor and the resulting sinusoidal collector voltage is cut to near zero volts, what is the state of the transistor? Please select one: a. answers B and C b. interrupted drive c. answers A and C d. forced into nonlinear operation e. drifting into saturation
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
2. A full wave rectifier is used to convert 400 Hz ac todc Design a full-wave rectifier power supply that will deliver a dc outpu voltages 15V and the load current is 1A. ERS
A single-phase full bridge uncontrolled rectifier is supplied by 220 V (rms) line voltage. The load is pure resistive. What is the output Ripple Factor ?
A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load resistance of 100 ohms. What are the average values of load voltage and current when firing delay angle is; 1. 140 degrees. 2. 30 degrees.
a. What are DC Choppers? Explain what TRC (Time Ratio Control) is b. A Buck Converter is used with a 2mH inductor and a supply voltage of 15V. The load resistance is maintained at 1 Q. The switching frequency is 100 kHz. i. Determine the duty cycle needed for an output voltage of 5V. ii. Calculate the output supply voltage ripple. iii. What are the consequences of decreasing the load resistance by 50% (to 0.5 ohms)? c. Identify the class of converter in the figure and describe the principle of operation of such a converter. d. State a possible application of such a converter. e. Draw the output waveforms of the current and voltage and the gate pulses of the choppers. Indicate on the current waveform the region of operation of the choppers and diodes. CH₁ CH₂ AD₂ Chopper wwwroo E +← Vo
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
A single-phase half-wave controlled rectifier connected to 120V, SOHZ supply to feed load resistor 5a. If the fire angle (a) adjusted to give the maximum output for the rectifier. Calculate and draw the following: a DC Power b- AC Power e- The rectification eli ency d- Draw the signals (VS, Pulses, V output and VT). single-phase half-wave
Consider the half wave rectifier is supplied with 115V, 80HZ signal. Assume the number of turns in the primary to secondary ratio is 10:4. a. Calculate the average dc current through the load resistor 3.5K2. b. Calculate the value of input ac power, output dc power and frequency of pulsating dc output.