R2= 8ΚΩ Μ R1=4ΚΩ Μ R4= 24ΚΩ R3=12ΚΩ + V4 | 15 1 Is E=72V| + R5=12kΩ R6=12kΩ Μ 16 R1 R7=9ΚΩ Μ R9=6kΩ R8=3ΚΩ M

Q: What is program block and module .What is difference between "==" and "==="

A: Program block is new construct in System Verilog. The blocking and non blocking statement should not…

Q: 5. What is the function of the digital circuit shown below? Describe its operation briefly and find…

A:

Q: 2. Convert from Binary to Gray code: 11010100102 = _______________________ Gray code 3. BCD…

A:

Q: For proper operation of an N-channel JFET the gate voltage needs to be _____ with respect to the…

A: in JFET current through the device is controlled by the application if gate current .  There are two…

Q: In a self-biased JFET circuit, the gate bias voltage is actually developed as a voltage a. load…

A:

Q: 4. Build an AND gate using transistors, switches and LEDs. Pressing the switch should emulate…

A:

Q: The mass of a large computer system is 290 lb. How many kilograms is this mass?

A: Given data, The value of mass of computer is 290 lb. Since 1 lb = 0.453592 kg

Q: Make a list of three technologies that have gone from analogue to digital. What was the reasoning…

A: Analog devices works on a continuous type signals while digital signal works on discreate type of…

Q: Derive the transfer function for the circuit shown below R₁ Å} iz eo Gro e₁ E1(s) Eo(s) (Voltage…

A:

Q: In CE configuration which of the below terminal is common for both input and Output. a. All the…

A: In the CE configuration, The output is taken between the emitter and collector terminal.And the…

Q: The term accuracy describes the maximum expected error associated with a measurement

A: Accuracy will describe the maximum expected error associated with measurement and sensor.

Q: Distinguish between ‘Analog and Digital signals’.

A: Analog signals A continuous signal called an analog signal substitute one time-varying quantity for…

Q: 9

A: For 9th question The given memory types are 1.ROM 2.RAM 3.EPROM 4.EEPROM For 10th question Sine wave…

Q: Find and draw the Thévenin equivalent circuit for the network external to the resistor R for the…

A:

Q: Question 4: what is the effect low cost operation amplifier in optical fiber system ?

A: Optical fibres are most commonly employed to convey light between the fibre's two ends, and they're…

Q: Q1. Convert the 1604 into a binary number.

A: Since, the radix of the given number i.e. 1604 is not mentioned in the given question.  So,…

Q: For an analog to digital conversion using 10 bits in a O to 5 volt range, what is the digital…

A:

Q: Have a look at the problems that have surfaced because of the widespread use of digital materials.

A:

Q: What are the different types of memories and what are the applications they are used for?

A: Different type of memories

Q: The JFET terminals that are connected to thechannel are the A. Gate and sourceb. B. Drain and…

A: Drain and source are the  JFET terminals that are connected to the channel.…

Q: 47. The arrow in a JFET points a. Away b. Towards the n-type material. c. Cannot be determined d.…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Q: why the silicon crystal is preferred in the making of the electronic components?

A: Silicon is a semiconductor. It shows conduction property of metal at certain conditions and also can…

Q: The open circuit imepdance of a certain length of a loss-less line is 100 ohm. The short circuit…

A: Given: Open circuit impedance of line, Zoc=100 Ω Short circuit impedance of line, Zsc=100 Ω

Q: Find the current I1 through R1 for the network method in Figure below.

A: Given circuit is,Asked to find the current I1 through resistor R1

Q: The following program is supposed to add the contents of memory location 2050H to the accumulator.…

A: When the above program is executed once, the contents of the accumulator will get updated with the…

Q: How does a transistor compare to a physical switch in a digital circuit? Use illustrations.

A: As we know that transistor works as a switch in saturation region or in cutoff region. Cutoff region…

Q: a. Find and draw the Thévenin equivalent circuit for the network external to the resistor R for the…

A: In this question, we need to determine the Thevenin equivalent across the terminal resistance R and…

Q: Give several examples of I/O devices.

A: I/O devices are those devices which can be used as a link in middle of the human and the computers.…

Q: 1. Write the data (10010000)Gray in BCD code.

A:

Q: What is the meaning of the following abbreviations : PAM, PDM, PPM

A: According to the question we have to discuss about PAM, PDM, PPM.

Q: When comparing a gate and a circuit, what are the key distinctions?

A: In the field of digital electronics, gates and circuits play fundamental roles in designing and…

Q: SV What is assertion. what are various step of assertion

A: To verify a design we write test bench to check that it meet specification. Verification can be done…

Q: Using the superposition theorem, determine the current through the 24 Ω resistor of Figure below.…

A:

Q: If the range of measurement is from -2 V to 2 V, what should the number of bits of the ADC be in…

A: The voltage span is 2--2=4 Resolution given is  0.125 V

Q: When a circuit symbol has no bubble and there is no line above the signal name, the line is said to…

A: bubble or line above the name incicates the signal wherether it is active high or low

Code Conversion

The method or technique used to convert code from one format to another is termed code conversion. Code conversions are most commonly used in computers, digital electronics, microprocessors, etc.