R17-4. A 20-kg roll of paper, originally at rest, is pin-supported at its ends to bracket AB. The roll rest against awall for which the coefficient of kinetic friction at C isHc=0.3. If a force of 40 N is applied uniformly to the end ofthe sheet, determine the initial angular acceleration of theroll and the tension in the bracket as the paper unwraps.For the calculation, treat the roll as a cylinder.1312120 mm60°P = 40 N

A free-body diagram of the roll paper is given as, On taking force equilibrium in a horizontal…

Answered: R17-4. A 20-kg roll of paper,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The uniform cylinder has a mass of 30.0kg and is rotating about a horizontal axis through O at 1200 rpm. The coefficient of kinetic friction between the cylinders and braking levers is 0.200. If the spring tension is 100 N, calculate the time required for the cylinder to stop spinning.
The 136-kg spool has a radius of gyration about its mass center of kg = 300 mm. If the couple moment is applied to the spool and the coefficient of kinetic friction between the spool and the ground is u: = 0.2, determine the angular acceleration of the spool, the acceleration of G and the tension in the cable. (Figure 1) Part B Determine the acceleration of G. Express your answer to three significant figures and include the appropriate units. HA ac = Value Units Submit Request Answer Part C Figure Determine the tension in the cable. Express your answer to three significant figures and include the appropriate units. 0.4 m В HA 0.6 m T = Value Units M = 450 N-m Submit Request Answer
Q5: The 15 kg cylinder rotates with an angular velocity of 40 rad/s. If a force F = 6 N is applied to the AB bar, as indicated, determine the time required to stop rotation. The coefficient of kinetic friction between the bar and the cylinder is 0.4. Disregard the thickness of the bar. F = 6N 400 mm- 500 mm B 150 mm-
The 30-kg wheel is rolling under the constant moment of M = 84 N.m. The wheel has radius r = 0.48 m, has mass center at point G, and the radius of gyration is kg = 0.24 m. The coefficients of friction between the wheel and the ground is μ = 0.39 and k=0.10. If the wheel rolls without slipping, determine the angular acceleration of the wheel (in rad/s²). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answer G 1
The 100-kg thin circular disk rolls without slipping on the horizontal plane. Determine a) The angular acceleration of the disk. b) The friction acts on the disk.
The 29-kg spool of outer radius ro=530 mm has a centroidal radius of gyration k=355 mm and a central shaft of radius ri=215 mm. The spool is at rest on the incline when a tension T=204 N is applied to the end of a cable which is wrapped securely around the central shaft as shown. Determine the acceleration aaa of the spool center GGG and the friction force FFF acting at the interface of the spool and incline. The friction coefficients there are μs=0.28 and μk=0.17. The tension T is applied parallel to the incline and the angle θ=16. The acceleration aaa and the force F are both positive if up the incline, negative if down.
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 750 kg and an average gear-tooth force of 2.65 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 155 mm, R = 660 mm, 0 = 20° Detail of contact at B Answer: x = i B R →→→ G mm
Problem 1: The uniform drum shown weighs 80lb and has a radius of 0.5ft. Starting from rest, the cable wrapped around the drum is subjected to a vertical force P which resulted in a constant angular acceleration of 20 rad/s. Determine magnitude of P and the reaction at the support pin at O. Neglect the mass of the cable d = 20 80 - 2.48 32.2 r-0.5 %3D
The 25-lb slender rod has a length of 6 ft . Using a collar of negligible mass, its end A is confined to move along the smooth circular bar of radius 32? ft . End B rests on the floor, for which the coefficient of kinetic friction is ?B = 0.52. The bar is released from rest when theta is 30 degrees. Find the angular acceleration of the rod (Please type answer no write by hend))
The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degrees a) draw the free body, kinematic and kinetic diagrams for the bar, b) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, c) determine the angular acceleration of the bar and the reaction forces at ends A and B. *****MASS IS 10KGS NOT 10LBS*****
The 6-Kg package is just nudged from rest over the čdje of the chate, The coe fficient of Kine tic fhiction between peckage aad chate is he The ligit has stiffness 60 KNm and Spring initially undeformed. d is 4m- Mx 40° Find the coefficient of Kinetic friction if the maximum com pression of The sp ing is 50 mm.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS