Table (3.1)R1R2R1 and R2R1 and R2(WireResistance)V(Volt) I(Amp) V(Volt) I(Amp) V(Volt) I(Amp) V(Volt) I(Amp)5.9(CarbonResistance)(in Series)(in Parallel)0.844.65.80.522.810.713.90.865.20.462.40.884.40.623.20.74.20.382.20.83.60.522.20.530.2620.740.42.8plot the four lines on the same graph, add label for each lineadd the slope on your graph for each line using add trendline option. Y-intercept = 00.442.20.21.60.65. Compare the calculated values with the experimental values youobtained for:Combination of resistances in series:show your calculations for the Calculated value# Experimental value =# Calculated value =Combination of resistances in parallel:show your calculations for the Calculated value# Experimental value =# Calculated value =

Ohm's Law Ohm's law states that "if current is flowing through two points of a conductor, then the…

R1 R2 R1 and R2 (in Series) R1 and R2 (in Parallel) (Wire Resistance) V(Volt) I(Amp) V(Volt) I(Amp) V(Volt) I(Amp) V(Volt) I(Amp) 5.9 (Carbon Resistance) 0.84 4.6 1 5.8 0.52 2.8 1 3.9 0.86 5.2 0.46 2.4 2.2 0.71 0.88 0.62 3.2 4.2 0.38 0.8 0.74 4.4 0.7 3.6 0.52 2.2 0.5 3 0.26 2 2.2 2.8 plot the four lines on the same graph, add label for each line add the slope on your graph for each line using add trendline option. Y-intercept 0 0.4 0.44 0.2 1.6 0.6 5. Compare the calculated values with the experimental values you obtained for: Combination of resistances in series: show your calculations for the Calculated value # Experimental value = # Calculated value = Combination of resistances in parallel: show your calculations for the Calculated value # Experimental value = # Calculated value =

R1 R2 R1 and R2 (in Series) R1 and R2 (in Parallel) (Wire Resistance) V(Volt) I(Amp) V(Volt) I(Amp) V(Volt) I(Amp) V(Volt) I(Amp) 5.9 (Carbon Resistance) 0.84 4.6 1 5.8 0.52 2.8 1 3.9 0.86 5.2 0.46 2.4 2.2 0.71 0.88 0.62 3.2 4.2 0.38 0.8 0.74 4.4 0.7 3.6 0.52 2.2 0.5 3 0.26 2 2.2 2.8 plot the four lines on the same graph, add label for each line add the slope on your graph for each line using add trendline option. Y-intercept 0 0.4 0.44 0.2 1.6 0.6 5. Compare the calculated values with the experimental values you obtained for: Combination of resistances in series: show your calculations for the Calculated value # Experimental value = # Calculated value = Combination of resistances in parallel: show your calculations for the Calculated value # Experimental value = # Calculated value =

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

P 4.2-4 Consider the circuit shown in Figure P 4.2-4. Find values of the resistances R₁ and R₂ that cause the voltages v₁ and v₂ to be v₁ = 1 V and v₂ = 2 V. 3 mA Figure P 4.2-4 500 Ω m R2 5 mA
2. Consider the circuit shown in the figure. The current through the ammeter is zero. a) What is the potential difference between the points a and b b) What is the resistance R? 2 b) Question 2 part b (second part of question 2) O 40 020 8 Ω 10 Ω O 60 O Other: a 4 Ω 102 ww d 202 Ar N b
The capacitor is initially uncharged when the switch is closed at t=0. When t equals 10s what does the ammeter read? (In mA) a.0.10 b. 0.20 c.0.79 d.1.2 e. 2
Q2/ in an experiment measuring the internal resistance of a voltmeter you have the following readings Calculate the magnitude of each 1- The electromotive force of the continuous source E 2- The value of the internal resistance of the voltmeter Rv R(0) V(v) 1000 2.25 2000 1.8 3000 1.5 4000 1.28 5000 1.12 6000 1 7000 0.9 8000 0.81 9000 0.75
A capacitor is connected in series with a resistor and a switch. With the switch open, the capacitor is charged to 9.0 V. When the switch is closed, how long will it take for the voltage across the capacitor to drop to 6.0 V if the time constant of the circuit is 4.0 s? a. 0.3 s b. 1.2 s c. 1.6 s d. 2.7 s
14. Given the circuit. 10V 10 V What is the emf af the battery? 10 V 10 V a.5 V b.10 V G.20 V d.40 V 10 a 40 10 0 R-10 for all sources 15. Referring to the same circuit in the preceding problem, what is the terminal voltage of the battery? a.18 V D.19 V G.20 V d 38 V
What is the equivalent resistance for the resistors in the configuration below? 6.0Q2 10.0 Ω 2.0 92 www 4.0 92 22 W 13 W 2.3 W 5.2 W
24
What is the ratio of the total resistance in series to the total resistance in parallel if R1 = R2 = ....R5 = 50? %3D 25:1 O 1:25 2:12 12:2
Determine the voltage across the 5.0- resistor in the drawing. Number Units 5.0 22 10.0 V 10.0 Ω 10.0 22 -2.0 V 15.0 V
Refer to the given circuit. C1 = 5 µF C3 = 8 µF C2 = 4 µF C4 = 6 µF C5 = 4 µF DURACELL VT = 12 V How much voltage is taken by capacitor #4 (c4)? Select one: a. 7.2 volts b. 6.36 volts O c. 5.65 volts O d. 4.8 volts
What possible changes can be made to the circuit so that the capacitor will charge faster to its maximum voltage value?