R1L1D1400200mDR2V1160010The switch is closed for t<0 and opens at t=0. Determine the state of the diode and verify it.Assume an ideal diode. Write also the expression for vo(t) and sketch it.

Answered: Image /qna-images/answer/ef25c179-ba59-4bec-8002-d38e801c2896.jpg

Answered: R1 L1 D1 400 200m D V1 R2 1600 10 he…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
A half wave rectifier is shown below. The Diode with a constant voltage drop model (v=Von = 0.7V) Draw the input and output voltage waveforms for 0 < t < 2T. Assume that RC >> T and T >> delta T. At what time does the diode turn on? In the waveform in (a), f the cap discharges for 15msec, what is the ripple voltage and the RC time constant In the waveform in (a), if the diode conduction interval is 0.5 msec, what is the ripple voltage and the RC time constant? In the waveform in (a), if the output ripple voltage is 0.5v, what should be the RC time constant? What is the diode peak inverse voltage (PIV)? If you want to reduce the PIV of the diode by half, what would you do?
solve d-f
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
just The third and fourth question
Demonstrate clipping of negative waves with an inverted diode in the output.A circuit which removes the peak of a waveform is known as a clipper. Show a negativeProduce a schematic diagram.During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diodedoes not conduct. It is as if the diode were not there. Show the positive half cycle isunchanged at the output V(2). Show the output positive peaks overlays the input sinewaveV(1).Voltage values: Resistor valuse: 1 K ΩDC offset: 0 VAmplitude: 5 VFreq: 1 KHz
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
We know that the Si-diode will pass the current in a forward biased region. This behavior is useful for many applications. C)Plot the V-I Characteristic Curve of the diode.
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS

R1 L1 D1 400 200m D V1 R2 1600 10 he switch is closed for t<0 and opens at t=0. Determine the state of the diode and verify it. ssume an ideal diode. Write also the expression for vo(t) and sketch it. www