R1 100 R2 ww R3 2002 D R4 www 1002 1092 R5 R6 100

Q: The cylinder of an Ideal Dual Combustion has a bore of 7 inches and a stroke of 7.5 inches. The…

A: Stroke length, L=7inches=177.8mm=0.1778mDiameter of cylinder, D=7.5inches=190.5mm=0.1905mSpeed of…

Q: Water at 10 Cflows from a large reservoir to a smaller one through a 5-cm diameter cast iron piping…

A: Given Diameter of the pipe = 5 cm = 0.05 m Flow rate = 6L/s Density = 999.7 kg/ms Friction…

Q: Q.2 Draw the Shear Force Diagram and Bending Moment Diagram for the beam shown in Figure 2, where R…

A:

Q: Question No.3 dM The bending moment M of the beam is given by dx -w(l – x) where w is a constant %3D…

A:

Q: The clutch system shown in the figure is used to transmit torque through a 2-mm-thick oil film with…

A: Given: toil=2 mmμ=0.38 Ns/m2d=30 cmN1=1200 rpmN2=1125 rpm

Q: 150 200 mm D mm 150 150 v2 mm mm 0 = 45° E 12.5 rad/s

A: Given data,θ=45°ω=10 rad/sOB=1502mm=0.2155mAB=350mm=0.3556mO'A=150=0.1524m

Q: Determine the range

A: Given data: The magnitude of vertical weight, W = 1200 N. Coefficient of static friction, µs = 0.30…

Q: An isentropic air compressor takes 150 m/min of air in at 10°C and 100kPa and compresses it to 1000…

A: Given: Flow rate (Q)=150m3/min Inlet temperature T1=10°C or 10+273=283K Inlet pressure P1=100kPa…

Q: Q2) For the combined linkage mechanism shown in figure, a) Calculate the number of the degree(s) of…

A: Since you have posted a question with multiple sub-parts, we will solve first two subparts for you.…

Q: Figure Q4 shows a rod of negligible mass whose ends has to particles A and B which slides along the…

A: Therefore the position of center of mass will be at distance of “3L/4” from the end “A” and at…

Q: The tape shown slides around two fixed pegs each of radius 30 mm as shown. If T1 = (0.1P in newton)…

A:

Q: Calculate the per meter (of length) pressure drop (units: kPa) associated frictional losses (only)…

A:

Q: determine the tension in cable AC and in cable BC.

A:

Q: A 1200 Ibs force acts as shown on a 500 Ibs block placed on a horizontal plane surface. Determine…

A: .

Q: 1. Determine the component of each force along the specified x - y axes. Refer figu 1. the exclusive…

A:

Q: т, п + 1 2(T-1. + Tm.+1) + (Tm+1,m + Tm.n-1) т-1, л m, n m+ 1, n hAr hAr + 2 T - 2 3+ k %3D Ay m,…

A:

Q: A shock-free coupling for a low-power mechanical drive is to be made from a pair of concentric…

A: Given, Power,P=10WRadius of cylinder,R=10mmLength of cylinder,L=20mmN1=10000rpmMinimum gap…

Q: Consider the situation described in уг 1 Vi 1) by taking into account the speed V₂ of the fluid at…

A: Given : The free body digram is,Assumption : The area at the point 2 is much larger than at point 1…

Q: A dam on a river is built so that the wall facing the water is shaped like the region above the…

A: Given:The density of water is .The equation of curve is .The equation of line is .The water level is…

Q: Given, HRB = 4X Find BHN. Given, HRC = 3X %3D Find BHN.

A: Hardness : it is the property of the any material that tell the resistance ability to abrasion or…

Q: A rigid bar the fiqure . Cons fruct the the deg rees of freedom díffuse , Supporied by a massless…

A:

Q: A force of magnitude 1000 N passes from B (4,4,6) m to C (-4, 1,1) m. Calculate moment o this force…

A: Write the vector of BC. BC=C-B=-4,1,1-4,4,6=-8i-3j-5k   Calculate the unit vector of BC.…

Q: In figure Shown, felocity at Section-1, is 1.7 and density of water slog is 1.94 Sa. Neglect losses,…

A: Data given - Velocity at section 1 = 1.7ft/s Density of water = 1.94 slug/ft3 To determine - h= ?

Q: Choose the following and define also

A: Given; Wet steam flows through a throttle valve and remains wet at exit,Throttle valve is used for…

Q: Determine the resultant force that acts on the hook:

A: Write the expression of the force F1 in vector form. Write the expression of the force F2 in vector…

Q: 1. Find wn Is sm Ans. K I tmr

A: It is the basic numerical of mechanical vibration portion. First of all we have to find the…

Q: Consider the truss shown in (Figure 1). Suppose that Fi = 4.5 kN and F = 6 kN. After the truss is…

A: Given dataForce F1 = 4.5kNForce F2 = 6kNTo determine the forces in the members BC HC and HG

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.