R2R,1+-VEE =- 15 VV.outinR,R1R1 = 5.6 kQV outVinVcc =+ 15 VRin19) calculate the value of R2 required for a closed-loop voltage gain of 5V/V A) what is the Vin you set the DC power supply to?B) what is the measured open-circuit output voltage?c) what is the calculated gain?D) what is the measured source current?

Answered: Image /qna-images/answer/20331961-172b-43f3-b779-85c70854f055.jpg

Answered: R, =|1+ -VEE =- 15 V V. out R1 R, R1 =…

R, =|1+ -VEE =- 15 V V. out R1 R, R1 = 5.6 k2 V out Vin Vcc =+ 15 V Rin 19) calculate the value of R2 required for a closed-loop voltage gain of 5V/V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
(c) (d) Figure Figure Q1b shows an Op-amp with a bias current compensating resistor (Rp). R₁ V₂. Vp IB. R₂ W A • V₂ Figure Olb (i) Derive an expression for V. to quantify the effect of bias currents IB+ and IB-. [3] (ii) Explain how you would choose a value for Rp to reduce the output error due to the bias currents, IB+ and IB.. [3] Referring to an op-amp define what is meant by common-mode rejection ratio (CMRR) and explain the effect a finite CMRR would have on high-precision applications. [4] Page 2 of 7 Continued overleaf
A differential op-amp circuit as shown below is used to implement a given linear voltage measuring functionV = f(V,). ouf Provide answers to questions 19 – 22. ww V. V; W R out R2 Ground
3I Calculate the the Output Voltage of a non-inverting op-amp with the following parameters Rf = 360KOhms, Vo = -9.3V, and Vi = -0.3V. a.31.2 kOhms b.32 kOhms c.12 kOhms d.31 kOHms
answer the question
+Vcc Vin VI Vo Vref VN -Vcc Ry RxL Figure Q.A2(e). Inverting Schmitt-trigger circuit. (ii) The operational-amplifier (op-amp) of the inverting Schmitt-trigger in Figure Q.A2(e) has saturation voltages of +Vsat = +11 V and -Vsat = -11 V. The voltage divider circuit has the relationship of Rx = 2RY with the value of RY being 100 kn. Using the relationships derived above: (a) Calculate the values of the upper threshold point (UTP or Vi*), lower threshold point (LTP or Vr). (b) Now, sketch the input-output characteristic of the inverting Schmitt- trigger. Clearly label axes, the threshold voltages and the saturation voltages in your sketch.
Q4 Consider you have to design a convertor to produce an output voltage of 36 V from a 3.3-V input DC source. The output current is 0.1 A. The design of above convertor should be for the output ripple voltage of 2 percent. The effect of ESR should be considered having relation to the capacitor value by as, rc = 10-5/c Design the convertor subject to above mentioned design requirements and justify why a boost convertor will not be a good choice here.
please see the attached pic thank you
Figure Q2(a) shows an amplifier system with the given input voltagewaveform Vin and the corresponding output voltage waveform Vout. If a practical op-amp is used in the amplifier system in Figure Q2(a),calculate the closed-loop gain, ACL given that the open-loop gain, AOL =3000. You can use the value of resistances found in Q2(a)(i).
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
1- Mention any bwc advantages of integrated Circut. 2- For the circuit given below Vnis a sine wave Vinpp 11 Vand Vref-12V, Assume Vsat 1zv Name the circuit and drew the input and output waveforms. Vo Vin Vref 3- Explain why open-oop op-amp configurztions are not ues in linear applications Draw the biock diagram of opemp and define the funcion of each biock