Questions Q1. Find the average shear stress (t) on the 30 mm diameter hinges at A andB for the given load on the member. Note that XX is the last two digits of your ID. For example, if your ID is 12S14164, then applied load is to be taken as 64 kN. Please show ALL calculations and draw the required free body diagram. XX kN 3 1.3 m 2.5 m

Questions Q1. Find the average shear stress (t) on the 30 mm diameter hinges at A andB for the given load on the member. Note that XX is the last two digits of your ID. For example, if your ID is 12S14164, then applied load is to be taken as 64 kN. Please show ALL calculations and draw the required free body diagram. XX kN 3 1.3 m 2.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam has a maximum moment equal to 20 KN.m. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. What is the actual bending stress of the beam in MPa? Blank 1 (use two decimal places, no need for unit)\\ with complete solution
A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown. We know that the spacing be- tween the nails is s=50 mm and that the allowable shearing force in each nail is 300 N, calculate (a) the largest allowable vertical shear in the beam, (b) the corresponding maximum shearing stress in the beam. E 20 mm 80 mm 20 mm S 120 mm S
Problem 1 A truss is subjected to the loadings as shown in the figure. Determine the force at member JI, IC, CD, and DI. Use combined solution using Method of Section and Method of Joints. State wether the force is Tension or Compression. USE 3 DECIMAL ONLY. 10 m, 5 @ 2 m 3 kN 6 kN 4 kN 3 kN 1.5 kN K Jooo o foo 00 F 5 m 9 kN B A Figure 1.0
Given the truss and loading shown below, determine the stress at member AB if Pu = 18.375 Kips and its area is 23 in². Assume that the truss are simply supported at joint M and E. Express your answer in ksi. Use three decimal places. RM Pu Pu 0 Pu Pu 8@10' 80' Pu B Pu L K J I H G 8@10' 80' Pu D LL F E RE
how to solve this one fast please
* For the beam and loading shown with P = 2 kN, consider section n-n and determine (a) the largest shearing stress in that section, (b) the shearing stress at point A. Problem #1 1m C n 2 m B -1 m- -150 mm- 125 mm 200 mm 25 mm 25 mm Pt. A is just below 25 mm
Determine the maximum magnitude of load P that can be applied to the truss. The maximum allowable tensile force in the members of the truss is (Ft) max = 5.2 kN, and the maximum allowable compressive force is (Fe) max = 3 kN. Take d = 2 m. (Figure 1) Figure 1 of 1 E d/2 C PV d/2 <
1) will upvote anyone who will answer correctly. thanks
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
A joint in a wooden structure shown has an applied loadF = 50 kN along the axis of the slanted member with anangle of 30°. Determine the bearing stress developedalong the plane ABC.Answer: σb ___________________
E=210GpaEach member has a solid circular cross section with a diameter of D=5.98mm with a length of 240mm for the horizontal and vertical members. Maximum load of F = 350N. Find the stress and internal axial force in each truss member using the true strain results in the table for each load step.
SITUATION 2: A double-angle tension member, 100 mm x 100 mm x 8 mm is subjected to a tensile load, P= 210 kN. The diagonal member is on a slope 2V:1H and is connected to a supporting beam by a wide tee. S1= 38 mm t1= 16 mm S2= 75 mm t2= 16 mm S3= 100mm t3= 16 mm Allowable strength and stresses: Yield strength, F,= 248 MPa Ultimate Strength, F= 400 MPa Bolt shear strength, F,= 150 Mpa Bolt Tensile Stress, F;= 195 Mpa Bolt Bearing Stress, F,= 1.2Fu Assume that the bolts are equally Loaded. 1. Determine the required "d," of the 3 bolts in shear connecting the double-angle member the wide tee. Round your answer to whole number. 2. Determine the required diameter "d," of the four bolts in tension connecting the wide tee to the flange supporting beam Round your answer to whole number. 3. Design the diameter "d," of the four bolts connecting the wide tee to the flange supporting beam. Round your answer to whole number. 1p S2 S2 t1 t2 t3 S3