Question/Assignment: A saggar is a ceramic, boxlike container (round, oval or cubic in shape) used in the firing of ceramic wares, glass, gold etc., to protect ware or contents from the flame in kilns or furnaces. Traditionally, saggars are made primarily from fireclay. Saggars have been used to protect, or safeguard, ware from open flame, smoke and gases. Modern saggars or crucibles are made of alumina ceramic, cordierite ceramic, mullite ceramic and silicon carbide. Prepare a process route for the production sagger/crucible, that I can melt glass/gold in it, at a 1700°C. Can you give reasons for every stage of process? Key clues: fireclay grog, particle size distribution, plastic clay, forming and temperature

Question/Assignment: A saggar is a ceramic, boxlike container (round, oval or cubic in shape) used in the firing of ceramic wares, glass, gold etc., to protect ware or contents from the flame in kilns or furnaces. Traditionally, saggars are made primarily from fireclay. Saggars have been used to protect, or safeguard, ware from open flame, smoke and gases. Modern saggars or crucibles are made of alumina ceramic, cordierite ceramic, mullite ceramic and silicon carbide. Prepare a process route for the production sagger/crucible, that I can melt glass/gold in it, at a 1700°C. Can you give reasons for every stage of process? Key clues: fireclay grog, particle size distribution, plastic clay, forming and temperature

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

33 - Which of the following judgments is wrong for wood?A) It is possible to greatly increase the fire resistance of wood by injecting borax and aluminum salt chemical liquids into logs or coating them with non-flammable materials.B) Logs are cut mainly in 4 ways; parallel mower, prismatic mower, quarter mower and half mower.C) Dipping is the deep protection type of wood.D) It is immersed in a short or long-term hot antiseptic bath depending on the type of wood. For these baths, materials such as copper sulphate, zinc chloride and lysol are mostly used.E) The most negative side of wooden material is its lack of fire resistance. Impossible to completely save lean wood from fire effect
I need the answer as soon as possible
Thermal conductivity, specific heat, thermal diffusivity, and coefficient of thermal expansion are the four significant thermal properties of wood.
An engineering design requires a glass component to withstand high service temperature of around 1050°C (-1830°F) (Figure 3). A second requirement is that plastic deformation of the component is not allowed at this temperature. For each type of glass given below, briefly explain why it can or cannot be used in this application (a) Soda-lime glass: (b) 96% Slica Glass: () Fused Silica. Use the editor to format your answer
I need the answer as soon as possible
What is the process of Basic Oxygen Furnace (BOF) Steel Making Process?
20. The W59 code recommends minimum requirements of preheats. If you are welding a butt weld that is 4 inches thick in mild steel material with a carbon content of 0.3%C. Preheat is specified to be 250'F. What is the minimum width of the preheat zone from the centerline of the butt weld: a) b) inches on each side of the weld on the top of the plates inches on each side of the welding on the top and bottom of the plates I.
Can you explain how sanitaryware ceramics manufacture? What do we do in casting and drying steps? Thank you
Q5 Show by free hand sketch only for 5 of the following 1- The phase diagram for 2 metals completely soluble in solid and liquid state. 2- The effect of process annealing on the properties of cold worked metals. 3- The effect of carbon percent on the mechanical properties of hypo and hyper steel. 4- Die drawing of round rod. 5- T.T.T diagram. 6- Cluster mill process.