Question Two: The laboratory test data for a modified Proctor test and CBR test for (crushed limestone) are given below; Find the CBR value at 95% of MDD after necessary corrections, for the tested sample depending on Iraqi Specifications, R6 (after drawing the curve and stating your answer about which sort of sub-bases materials are used in highway construction?

Question Two: The laboratory test data for a modified Proctor test and CBR test for (crushed limestone) are given below; Find the CBR value at 95% of MDD after necessary corrections, for the tested sample depending on Iraqi Specifications, R6 (after drawing the curve and stating your answer about which sort of sub-bases materials are used in highway construction?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The laboratory test data for a modified Proctor test and CBR test for (crushed limestone) are given…

A: First we draw the graph penetration vs load If the concavity occurs in the graph we make one…

Q: Binder grade of asphalt selected for a highway construction based on the temperature records found…

A: Binder grade of asphalt PG70-16.

Q: Question Two: The laboratory test data for a modified Proctor test and CBR test for (crushed…

A: Since the concavity curve so we have to draw a tangent on the concavity part, the tangent cut the…

Q: The following results were obtained for an asphalt binder. Determine if the binder meets the…

A: To determine - If the binder meets the Superpave specifications for the followinga) Rutting b)…

Q: A 1775g of coarse aggregates was soaked for at least 24hours prior to the lab. It is then brought to…

Q: Question 5 v Saved What is the minimum acceptable compressive strength o GDOT class "AA" concrete?…

A: Since the question number to be solved is not specified, the solution of Question 5 is as follows:…

Q: Compute individual percent retained, cumulative percent retained and percent passing. 2. Make a…

A: Sieve size wt. retained % retained wt. passing % passing % retained GS % passing Cumulative wt…

Question

%CBR According to Iraqi Specification for different layers:
Layers
Compacted sub grade
Sub-Base
Base
%CBR (lower limit)
4%
30%
35%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Solution :

VIEW

Step 2: Explanation :

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Mass and mass related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A contractor claims that the mean compressive strength for a concrete mix is 4,830 psi and that it has a standard deviation of 430 psi obtained from testing 22 specimens. If you break 20 cylinders and obtain a mean compressive strength of 4,450 psi and a standard deviation of 480 psi, would you believe the contractor’s claim? Why? (With a 95% confidence interval)
An asphalt sample which is claimed to be AC- 20 is tested by an agency. Which test result will reject the sample O Viscosity at 60•C on original sample = 1850 Poise Ductility at 25C on TFO aged sample = 27 cm Penetration at 25 •C = 51 O Viscosity at 60 C on TFO aged sample = 11250 Poise
PLease answer the question in the picture please, show all of your work please and post pictures of your work, Do not type it!
(c) Asphalt concrete mixture of AC 14 will be used to construct the wearing course layer. The coarse aggregate, fine aggregate and filler are used as materials to produce the asphalt concrete mixture. The aggregate gradation will be blended to fulfill the gradation limit according to JKR standard specification as shown in Table Q1(c)(i). Based on this statement, conclude the result of sieve analysis test of blended aggregate as shown in Table Q1(c)(ii). I Table Q1(c)(i): Gradation specification for AC 14 mixture BS Sieve Size (mm) Percentage passing by weight 28.0 20.0 14.0 10.0 5.0 3.35 1.18 0.425 0.150 0.075 100 90-100 76-86 50-62 40-54 18-34 12-24 6-14 4-8 I Act Go to
Table shows the grain size distribution for two aggregates and the specification limits for an asphalt concrete. Determine the blend proportion requiredto meet the specification and the gradations of the blend. On a semilog gradation graph, plot the gradations of aggregate A, aggregate B, the selected blend,and the specification limits.c
5.41 Aggregates from three sources having the properties shown in Table P5.41 were blended at a ratio of 25:60:15 by weight. Determine the properties of the aggregate blend. TABLE P5.41 Property Coarse aggregate angularity, percent crushed faces Bulk specific gravity Apparent specific gravity Aggregate 1 73 2.774 2.810 Aggregate 2 95 2.390 2.427 Sand N/A 2.552 2.684
Problem No. 1A flexible pavement for an urban interstate highway is to be designed using the AASHTOmethod to carry a design ESAL of 3 x 106. It is estimated that it takes about a week for water tobe drained from within the pavement and the pavement structure will be exposed to moisturelevels approaching saturation for 30% of the time. The following additional information is available: Elastic modulus of asphalt concrete = 450,000 psiResilient modulus of base material = 35,000 psiResilient modulus of subbase material = 15,000 psiCBR of subgrade material = 8(a) Consider designing the same pavement with only asphalt concrete and base layer (excluding subbase layer). Use the information provided in Problem 1. (b) Compare strengths and weaknesses of each design.
For this problem, I need help understanding the data I am supposed to use to graph the needed graphs for this question and how these graphs are supposed to look.
Students in the materials lab performed the specific gravity test and bulk unit weight and voids of aggregate on a sample of coarse aggregate and obtained the following data: Mass of oven dried aggregate: 1042 g Mass of aggregate submerged in water: 646 g Mass of saturated surface dry aggregate: 1058 g Bulk dry specific gravity of aggregate. Find the absorption of aggregate. If the dry rodded unit weight of aggregate found to be 1695 kg/m3 , calculate the percent voids between aggregate particles in this test. We blend this aggregate with other aggregate with bulk dry specific gravities of 2.23. Calculate the bulk dry specific gravity of the blend if the blend proportion is 40:60.
i need the answer of all parts
QUESTION 1 A drum mix asphalt plant is different than a batch mix asphalt plant. O True O False QUESTION 2 Excess asphalt mix is kept in a grain silo until trucks transport it to the job site. O True O False QUESTION 3 Typically, ODOT calls for minimum 7" layer of surface asphalt mix to be placed and then a 4" layer of aggregate base beneath. O True O False
Using online resources, find the aggregate specifications for the state of California and identify the limitations for deleterious materials in aggregates used for asphalt concrete