Question: In A Dual- Combustion Cycle, The Maximum Temperature Is... In a dual-combustion cycle, the maximum temperature is 2000 ?C and the maximum pressure is 70 bar. Calculate the cycle efficiency and the mean effective pressure when the pressure and temperature at the start of compression are 1 bar and 17 ?C, respectively. The compression ratio is 18/1.

Q: Q-6: Blocks A and B are identical with each weight of W. If the coefficient of static friction…

A:

Q: where did 144 come from

A:

Q: solution incorrect resolve again

A:

Q: resolve solution

A:

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: S0ON so

A:

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: Answer in number 7 and 8.

A:

Q: Determine Stres

A:

Q: what is 1.54 from?

A: Given:The length of CD is .The length of BC is .The length of AG is The length of AD is .Consider…

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: Tät-/e205+(17-78 2.

A: Given Data⇒a↦=202+17.782

Q: 200 mm В

A:

Q: what is part number 4

A: Solution:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Create an example of Hooke's Law

A: To create: The example of Hooke's law. Concept used: Hooke's law: Hooke's law states that the…

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =…

A:

Q: ********** QI/A/ The 4-mm diameter cable BC shown in Figure Q1-4 is made of a steel with E-200 GPa…

A:

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Q: (12m) ladder weighs 200N and is ed against a smooth vertical wall its lower and (6m) from the wall

A:

Q: what is the actual area in part a ?

A: Given: Q=5000 m3/min=5000m3min×1min60 sec=83.33 m3/s V=6.0 cm/s=6.0cms×1m100cm=0.06 m/s

Q: number d and e?

A: To solve this question, we will use the moment equilibrium equation which is mentioned in the…

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.