Question- For a single phase 440/110 V transformer having input on primary side at no load is 100 W. The low voltage winding is kept open & the no load power factor is 0.4. Determine the active & reactive component of current at no load condition?

Question- For a single phase 440/110 V transformer having input on primary side at no load is 100 W. The low voltage winding is kept open & the no load power factor is 0.4. Determine the active & reactive component of current at no load condition?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Related questions

Q: Q. 36 Drive EMF equation of transformer and explain Primary winding, Secondary winding and…

A: Transformer - A transformer is a device that is used to transmit electrical energy. The transmission…

Q: 3.16 A single-phase, 50-k VA, 2400/240-V, 60-Hz distribution transformer has the following…

A: It is given that:

Q: Name three types of transformer and brief about each.

A: 1. Step Up Transformer and Step Down Transformer: Generally these Step up and step down transformers…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Question.

Single phase transformer.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data-

VIEW

Step 2: To Find-

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
What conclusions we come up with after doing open circuit test on single phase transformer.
If we increase the load than core loss and copper loss will... Decrease Increase Remain same
9. A single-phase transformer has a turn ratio of 6, the resistances of the primary and secondary windings are 0.9 £2 and 0.025 2 respectively and the leakage reactances of these windings are 5.4 92 and 0.15 2 respectively. Determine the voltage to be applied to the low- voltage winding to obtain a current of 100 A in the short-circuited high voltage winding. Ignore the magnetising current.
Find full load current..
dc tansformd
Can you solve D and E
??
3. A single phase, 50-Hz transformer has 80 turns on the primary winding and 400 turns on the secondary winding. The net cross-sectional area of the core is 200 cm. If the primary winding is connected to 240-V, 50-Hz supply, determine (a) the emf induced in the secondary winding, and (b) the maximum flux density in the core 2000 1
P2-Draw the equivalent circuit of a single-phase transformer and explain how the core losses are almost invariant to the load (current). How do they depend on the terminal voltages of the transformer? Also, using the equivalent circuit explain how the copper losses depend on the load current.
The windings of an 11500/2300V two winding transformer are connected in series, with 11500 V as the supply to the primary, to create an autotransformer. What is the voltage output of the resulting step-up autotransformer when Ip and Is are 10 A and 50 A, respectively?
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?