Question: A shunt-connected DC motor operates at its rated terminal voltage. Its no-load speed is 200 radian/second. At its rated torque of 500 Nm, its speed is 180 radian/second. The motor is used to directly drive a load whose load torque T₁ depends on its rotational speed wr. Neglecting rotational speed wr (in radian/second), such that TL = 2.78 x Wr. Neglecting rotational losses, the steady -state speed (in radian/second) of the motor, when it drivers this load, is

Question: A shunt-connected DC motor operates at its rated terminal voltage. Its no-load speed is 200 radian/second. At its rated torque of 500 Nm, its speed is 180 radian/second. The motor is used to directly drive a load whose load torque T₁ depends on its rotational speed wr. Neglecting rotational speed wr (in radian/second), such that TL = 2.78 x Wr. Neglecting rotational losses, the steady -state speed (in radian/second) of the motor, when it drivers this load, is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 50 kW induction motor is operated at a lagging power factor of 0.8, the source voltage being 230 V rms. a) Find the complex power Sm that this motor is using. b) In order to get lower electricity bill it is desired to connect a parallel compensator to the motor so as to get pf%3D0.95 lagging and still provide the 50kW real power for the motor. Determine the total complex power ST= Sm+ Sc that will achieve the desired pf, where Sc is the power of the compensator c) Determine the complex power S. of the compensator and the . value of the parallel compensator impedance. What type of circuit element should be the compensator?
Induct.motor.
If the average pole flux of a dc machine with 24 coils, each of which contains 16 windings, 4 poles, double layered parallel winding (duplex lap winding), with a speed of 1000 rpm, is 15mWb, what is the idle winding voltage and (Note: In your operations, two digits after the comma) take it)
10. The rotor of an 8-pole, 50-Hz, 3-phase induction motor has a resistance of 0.2 2/phase and runs at 720 r.p.m. If the load torque remains unchanged. Calculate the additional rotor resistance that will reduce this speed by 10% [0.8 2 (City & Guilds, London)
Angular speed of a DC motor running at a speed of 1200rpm is ................. Answer
Subject: Electrical Machines
Solve as soon as possible
A 6-pole alternator running at 1000 rpm, supplies an 8 pole induction motors. Find the actual speed of the motor if the slip is 2.5%.
A motor’s rotor spins at 1,000 rpm when no load is applied (i.e. torque = 0), but reduces to 900rpm when the rated torque of 2.3 N-m is applied. Determine the speed regulation and output horsepower at the rated load condition. If the motor’s input power is 500 Watts at the rated load condition, what is the efficiency?
A DC motor has an equivalent circuit shown below. The motor is driving a load, and it draws an armature current of 514A while running at a speed of 1700 rpm. The total rotational losses under this condition are 380 W. The input power to this motor in kW is RA-0.20 N.-1700 rpm Rad Re-1250 V-230 V R OA 12.25 B. 11.82 9C.12245.20 D.1224.52 Clear my choice
The developed torque of the dc motor at standstill is: Select one: O Lower compared with AC motor Several times greater than the torque developed by an AC motor of equal size and speed O Similar to AC motor