Question: A certain resistor has the following color code: orange, orange, red, gold. Determine the maximum and minimum currents you should expect to measure when a 12 V source is connected across the resistor.

Question: A certain resistor has the following color code: orange, orange, red, gold. Determine the maximum and minimum currents you should expect to measure when a 12 V source is connected across the resistor.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 5VE

See similar textbooks

Similar questions

A moving coil instrument has full scale deflection at 50 m V and 10 m A . the value of shunt resistance required to be connected to convert it into (0-5 A )ammeter is :
The maximum output voltage of a certain low-pass filter is 15 V. The output voltage at the critical frequency is O 15V O OV O 10.6V O 21.21V
Op-amp According to the information below, you need to answer the questions given by setting up the Op-amp circuit. is requested. Vin = -1 volt Desired Vout value will be 16. Note that a positive value is requested. Only resistors with 1k, 3k, 5k, 7k and 11k ohms can be used. The V+ value of the LM741 IC to be used for the op-amp will be 20 volts and the V value will be -20 volts. You need to use at least one inverting amplifier and non-inverting amplifier to create the circuit. 1)Write how you should find the Vout value. 2)Write the gain formula of the circuit and calculate it. 3) Build the circuit in any simulation program like Proteus and get the outputs.
answer in steps.
Number 33
Practical Usage of Logic Gates Design Problem A motor car manufacturing company has manufactured a motor car protecting circuit to warn if there is a movement in the car when the engine is not on or when there is damage to a shutter. This has three sensors to detect whether the engine is on and another sensor to detect whether there is a damage to a shutter. Another sensor is there to detect whether the car is moving. This circuit is designed with three basic circuits. One of these is a NOT gate and the other two gates should be included in the empty boxes. What are the logic gates suitable for these? Draw the circuit. Practical Usage of Logic Gates Engine sensor Shutter damage alarm signal sensor Movement sensor
A taco generator is use as a sensor to detect the speed of a rotating motor. The o/p of the tacho is between Ov and 5v where the midrange (2.5v) is equivalent to that the motor is standstill. When motor accelerates CW toward full speed, the tacho o/p will vary from 2.5v to 5v and when the input of tacho varies from 2.5v down to Ov means the motor is accelerating towards cCW. The Scenario is to reflect the equivalent speed on two SSDS which one will read the equivalent speed of reading 5 for maximum Cw (5v) and the other will also read 5 for maximum CCW (Ov) equivalent speed in the reverse direction. Taco generator input is connected to PA4, the CW SSD on PORTB and the CCW SD on PORTC Write ATmega 16 program sketch to follow the above scenario REFS1 REFSO Voltage Reference Selection AREF, Internal Vref turned off AVCC with external capacitor at AREF pin 1 Reserved 1 Internal 2.56V Voltage Reference with external capacitor at AREF pin ADPS2 ADPS1 ADPSO Division Factor 2 1 1 1 1 16 1 32 1…
When the input to an inverter is LOW (0), the output is(a) HIGH or 0 (b) LOW or 0 (c) HIGH or 1 (d) LOW or 1
You are to design a simple power supply made up of recycled electrical parts to drive a motor. To simplify the design, you can model the running motor as a load resistor. The motor is rated for 20V and draws 100mA when running. 120Vrms Resistor 60HZ Vp Vs 0° + C1 1250pF a = 3.75 Zener "Motor BR805D а. If you were to model the running motor as a resistor what would the resistor value be? b. The transformer has a turns ratio a = 3.75. What are the RMS and Peak values of the secondary voltage? What is the peak voltage after the diode rectifier bridge (without C1, Zener, resistor, or load)? Draw the waveform. d. Determine the ripple voltage (VRIPPLE) without the Zener diode in the circuit (assume the Resistor above is 1002). Determine the part number of a suitable Zener diode to provide an output voltage of approximately 20v. (i.e. 1N4 C. е. 2.
QUESTION:4 A 10k2 resistor is to be designed to handle a current density of 50A/cm? when a 5V is applied. If this resistor is limited to electric field of E =100 cm?/V-s, calculate: i current passing through the resistor ii cross-sectional area iii length of the resistor iv conductivity v carrier concentration
Design the following filter using filter design theory. LOW-PASS FILTER A low-pass filter is required to have a voltage gain of 1 in the pass band, to be 3 dB down at the cut-off frequency of 1.5 KHz and to be at least 80 dB down at 15 KHz. The design is to be a Butterworth filter using VCVS circuit (Sallen-Key).
1. By using the tincker-cad Set up the equipment as given below make sure the resistance value is 1K. CRO Ch-2 CRO Ch-1