ll SuperNe 4G3:00 PMC @ 6%Question 91 pointsSave APower supply circuit is delivering0.5 A and an average voltage 20 V to the load as shown in the circuitbelow. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constantvoltage model. The smoothing capacitor value is equal toI2-Dc 205A220V omsh5OHZO 001 FO 0 02 FO 00167 FO None of the above

This is a half wave rectifier with a capacitive filter. for this,the value of capacitor required is…

Question 9 Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltəge of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V msb 5OHZ: I2-Dc 20:5A VL-DC =20V O 001F O 002F None of the above

Question 9 Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltəge of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V msb 5OHZ: I2-Dc 20:5A VL-DC =20V O 001F O 002F None of the above

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the ripple factor for the filtered rectifier circuit below when RL= 4KO. Then explain briefly the effect of changing in the RL value on the output waveform. 5:1 Vp= 0.7v for all diodes Vma 100 V f= 60H2 D S0uF
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. 9kO IN1199C R2 01 18KO IN11990 D3 IN1199C R3 V2 12 V R4 5kQ
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
What voltage is boosted at the output of a multiplier. a) average b) rms c) peak d) instantaneous Which assumption is not used in the analysis of multipliers? a) a capacitor will not discharge b) start with the cycle of the source that will forward bias the nearest diode c) the output will always be multiplied d) a single diode is forward biased at a time A voltage multiplier a) multiplies the output voltage b) has very high voltage and low current c) can employ inductors d) may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations at a) the input and output b) the load c) source d) in the environment Between a lower percent regulation and a higher one, which is better? a) lower b) higher
5. Assuming an ideal diode, sketch Vị, Va and ia for the half-wave rectifier below. The input is sinusoidal waveform with a frequency of 60 Hz. Also, determine and sketch V, and i, Ideal V-2 V 2.2 ka R26.8 ka
Consider diode circuit shown below with Vcc=5V and V₂ = 3V. U₁A HH +V₂ ū The peak inverse voltage on the diode is close to V₁ V. A Vo
* When the peak output voltage is 100 V, the PIV for each diode in a center- tapped full-wave rectifier is (neglecting the diode drop) 200V O 100V 150V 55V If Vi is less than Vz. The Zener diode current is Zero Very low ********** High *< 0.5 A
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
B. For the circuit shown below, assume that the zener diode has Vz-3.3V and rz=092 when reverse biased, and has a 0.7V drop when forward biased. Fill the following table for values of Vo for different values of input voltage Vi. R1 Vi Vi -8V OV 8V 1k 5V N V2 R21k Vo Vo
The input to a 3-phase full-wave rectifier is 60 Hz AC voltage. If the voltage drop across diodes is 0 V, The RMS voltage at the load would be: O A. None of the other choices are correct O B. Cannot tell until we have more information O C. Lower than the RMS voltage at the input O D. Higher than the RMS voltage at the input O E. The same as the RMS voltage at the input
Assuming an ideal diode model for all the diodes in the circuit below, Calculate the voltage across and current flow through each diode 9kO 1N1199C R2 01 18kO IN1199C V2 12 V- R3 1kO D3 1N1199C R4 5kQ