B3 QUESTION 7Choose all that is true about "Cells" in Cellular Telephony.More than one choices are correct.Partial Marks AvailableNegative marks for incorrect choices.O Co-channel interference can be minimized by setting up antennas in particular direction.O Destructive intereference caused by waves taking multiple paths is generally frequency dependent.O Two mobiles sets using adajacent frequency channel can interefere with each other.O Even if a cell is not dropping calls due to congestion, cell splitting is still a good idea.U You need to at least use a micro cell if you want to cover a radius of 500 meters.O Base stations are always located at the centre of cellsQUESTION 8Consider a 10 Channel FDM system. The carrier frequency of the first channel is 10 KHz. The symbol time for each channel is 200us. The Guard Band between Channels is 1KHZ.The value of BWNOM will beKHz and and the signalling or Baud Rate will beKbps. The total Bandwidth required to multiplex these 10FDM channels will beKHz. If the same uses OFDM the total Bandwidth required to multiplex these 10 OFDM channels will beKHz.

As per guidelines, we have to solve only one queation. please upload the remaining question…

QUESTION 8 Consider a 10 Channel FDM system. The carrier frequency of the first channel is 10 KHz. The symbol time for each channel is 200µs. The Guard Band between Channels is 1KHZ. The value of BWNOM will be KHz and and the signalling or Baud Rate will be Kbps. The total Bandwidth required to multiplex these 10 FDM channels will be KHz. If the same uses OFDM the total Bandwidth required to multiplex these 10 OFDM channels will be KHz.

QUESTION 8 Consider a 10 Channel FDM system. The carrier frequency of the first channel is 10 KHz. The symbol time for each channel is 200µs. The Guard Band between Channels is 1KHZ. The value of BWNOM will be KHz and and the signalling or Baud Rate will be Kbps. The total Bandwidth required to multiplex these 10 FDM channels will be KHz. If the same uses OFDM the total Bandwidth required to multiplex these 10 OFDM channels will be KHz.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If triangular copper bus bar is 0.75 millimeter on the base and 100 millimeters in the height, find the cross-section. What is the cross-sectional area in square centimeters? Carry the answer to two decimal places.
Please provide Handwritten answer
What unit of measurement is used for fhe diameter of fhe wires
What is voltage
Needs Complete typed solution with 100 % accuracy.
QUESTION -8 The plot describing the thermal characteristics of copper wire is given in the figure. Using this plot, for a 1000ft length copper wire with 10 Ω resistance at room temperature (20oC)a) Calculate the resistance value at 100oC.b) Calculate the power consumed in the cable carrying 10A current at this temperature (100oC) in units Watt.c) Calculate the amount of energy consumed in the cable during a day with the conditions in (a) and (b) in units Joules.d) A motor with 600Watt output power that works with 85% efficiency is driven with 10A current carried in the cable at 100oC. Calculate the amount of power transformed (dissipated) into heat in this system.e) Consider that a cooling system is used to cool the cable to 50oC and the cable carries 10A current. How many watts should be the maximum amount of power consumed by the cooling system in order to gain power (consume less total power).
Problem 3: A factory manufactures a specific copper part. It is found at a certain temperature the resistance in m2 of this part is normally distributed with mean of 23.8 and standard deviation of 1.23. Among 5000 units of such parts, how many units are likely to have a resistance (a) less than 23? (b) greater than 24? (c) between 24.2 and 24.5?
Determine the resistance of a busbar made of copper if the length is 16 meters long and the cross area is a 5x5 sq. cm. Use 1.7241 micro ohm-cm as the resistivity. (Provide drawing or FBD)
Solution of part (d).
None
1. Solve the following resistance problems: a. A 4.2 cm long copper wire has a cross-sectional area of 3.7 mm?. Determine the resistance of that wire. Check the resistivity of Copper int the table given in the textbook. b. Consider a 1.6 cm long silver wire. What is the cross-sectional area of the wire for it to have a resistance of 2.2 x 102 0.
21 Balance is obtained in a DC potentiometer at a length of 71 cm when using a standard cell of 53.2 volts. Calculate the EMF of a dry cell if balance is obtained with a length of 20 cm. a. 0.07 b. 14.99 c. 0.01 d. 188.86