QUESTION 7 Figure 7 shows an assembly consist of circular shaft AB, solid circular BC and a circular CE. The shaft is made of titanium alloy steel and fixed at A. Segment AB is a hollow shaft, has an inner diameter of 25mm. While tube CE with the thickness 2mm has an outer diameter of 20mm. The assembly is subjected to torques of 1000 Nm at C, [X(30)+Y(50)] m at D and [X(50)+Y(30] Nm at E. The alloy has modulus of rigidity, G = 44kN/mm² a) Draw the torque diagram of the shaft. b) Determine maximum shearing stress developed in each segment. c) Calculate the angle of twist at the right end of the shaft.

QUESTION 7 Figure 7 shows an assembly consist of circular shaft AB, solid circular BC and a circular CE. The shaft is made of titanium alloy steel and fixed at A. Segment AB is a hollow shaft, has an inner diameter of 25mm. While tube CE with the thickness 2mm has an outer diameter of 20mm. The assembly is subjected to torques of 1000 Nm at C, [X(30)+Y(50)] m at D and [X(50)+Y(30] Nm at E. The alloy has modulus of rigidity, G = 44kN/mm² a) Draw the torque diagram of the shaft. b) Determine maximum shearing stress developed in each segment. c) Calculate the angle of twist at the right end of the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid 1.500-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 190 lb-ft and TD= 140 lb-ft, acting in the directions shown. Assume a = 42 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 20 ksi, determine the maximum torque TC that can be applied to the shaft.
TI=30NM, T2=155NM, T3=85NM and dBC=22mm. 12 010 T3 T2 T1 3-1892615112 D 010 b180106003- 1892615112 \dcp 1826151126 b180106003-18926 dBC B. `dAB b180100003-18926151126 In the figure above, torques TI, T2 and T3 are applied, respectively, to discs A, B and C on the shaft, which is fixed at point D. 3-1892815112s b180106003-18926 The diameters of the shaft segments are indicated in the figure and their values are given below (if they are required). Length of each segment on the shaft has the same value and is equal to L(AB)=L(BC)=L(CD)=400 mm. b180106003- 18926151126 Shear modulus of the material is 80 GPa. o-18926151126 b180108003-18926 Calculate the maximum shear stress g003-18926151126 003-18926 b18 on shaft segment BC. 010600s28151128 B A 46 MPa 60 MPа b180106003- 18926 b180106003- 1892615112 b180106003- 18928151126 38 MPa b180100003-1892615112 57 MPa b180106003- 18926151126 E b180108003-18928 31 MPа b180106003- 18926151126 b180106003- 18926151128 b180106003- 18928151126…
2) A shaft of a diameter of 30 mm is transmitting 14,9 kW at 400 rpm. The shaft is connected to a pulley of an axial length of 160 mm with the help of a rectangular key 16 mm x 12 mm ( b=16 mm, t=12mm). (The spokes are connected to the pulley, but the pulley is not shown in the figure). Axial length of the key, hub and pulley are 160 mm. Determine the shear and normal stresses developed in the rectangular key. Rectangular key Spokes A R Hub Shaft
I need answer in 10 minutes please quickly
Problem 3.55 not 3.54, problem 3.55
A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?
A solid steel [G= 12900 ksi] shaft with the diameter of d = 1.375 in. is subjected to torques TB = 250 lb.ft, TC = 300 lb.ft, and TD = 140 lb.ft, acting in the directions shown in the figure. Assume a = 48 in., b = 74 in., and c = 40 in. Determine the rotation angle of pulley C with respect to the support at A. In rad
The 140 mm long shaft shown in Figure 1 carries a two-gear wheel at each end. The gear wheel connected on left end has a mass moment of inertia of 15 kgm?. Whereas the mass moment of inertia of the gear wheel connect at right end of the shaft is 12 kgm?. The diameters of sections AB and BC of the shaft are 20 mm and 50 mm, respectively. If the modulus of rigidity of the shaft material is 80 GN/m, calculate the diameter of portion CD of the shaft that ensures that the node of the torsional vibration of the system will be at the centre of portion Bc. A 20 mm 100 mm 20 mm
O d. 25T Nm QUESTION 17 A stepped shaft subjected to a uniform torque T along its length is shown in the figure. When D = 2d, the angle of twist per unit length (0/L) of smaller diameter segment is, %3D O a. equal to that of larger diameter segment. Ob. twice that of larger diameter segment. OC.4 times (i.e. 22) that of larger diameter segment. O c. O d. 16 times (i.e. 24) that of larger diameter segment.. QUESTION 18
The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. Gst = 10.8(10³) ksi. (Figure 1) Figure sin. A 0.5 in. Jc 8 in D 500 lb-ft 12 in. 1 in. B < 1 of 1 Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μÅ Value 6 Request Answer Units www. ?
A solid constant-diameter circular shaft is subjected to the torques of TA = 560 lb·ft, TB = 1080 lb·ft, TC = 850 lb·ft, and TD = 330 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely.(a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6.(b) If the allowable shear stress in the shaft is 4200 psi, what is the minimum acceptable diameter for the shaft?
Question 48 A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)-28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T1" developed at left fixed support at a is____KN-m (A) 5.03 B) 3.82 C) 2.64 D) 0.48 (E) 1.18