QUESTION 6 The 6kg block is confined to move along the smooth parabolic path. The attached spring restricts the motion and, due to the roller guide, always remains horizontal as the block descends. The spring has a stiffness of k = 10N/m and an un-stretched length of 0.5m. a. Draw a free body diagram for the block. y = 2 - 0.5 x? www k = 10 N/m В 14 b. Write the general form of the equation of motion in the direction normal to the surface. c. Write the general form of the equation of motion in the direction tangential to the surface. --

QUESTION 6 The 6kg block is confined to move along the smooth parabolic path. The attached spring restricts the motion and, due to the roller guide, always remains horizontal as the block descends. The spring has a stiffness of k = 10N/m and an un-stretched length of 0.5m. a. Draw a free body diagram for the block. y = 2 - 0.5 x? www k = 10 N/m В 14 b. Write the general form of the equation of motion in the direction normal to the surface. c. Write the general form of the equation of motion in the direction tangential to the surface. --

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

/ The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying the loads shown, determine: (1) The maximum normal stress developed in each rod. (2) The horizontal displacement of end C with respect to the fixed support at A. (3) Suppose that only rod BC is exposed to change in temperature, what would be the change that keeps point C in the original position. Use Est = 200GPA, xst= 12(10)-6 600 mm 400 mm 50 kN 40 kN B C 50 kN
The stepped steel shaft carries the torque T. Determine the maximum allowable magnitude of T if the working shear stress is 22 MPa and the rotation of the free end is limited to 5.2°. Use G = 83 GPa for steel. Provide FBD T 80 mm 60 mm 4 m 3 m
Determine the magnitude of the pin force at A. Assume W = 530 Ib, a = 3.6 ft, b = 2.9 ft, r = 9 in. a a B A W D Answer: A = i Ib
Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression. B 15' C 15' D 14' A 15' G F 56° E 14 kips Answers: BC = kips CG = kips %3D
8 kN 4 m 15 kN 5 kN 2 m 2 kN 2 m 2 m A B с D E The aluminum rod shown has a diameter of 20 mm and is subject to axial forces acting at A, B, C, and D. Assume the rod has a Young's modulus of E = 70 GPa. a) State the internal axial forces within sections AB, BC, CD, and DE. Remember to indicate whether they are in tension or compression b) What is the displacement of A relative to C? c) What is the displacement of A relative to E?
It is made of solid circular cross-section bars, whose geometry and loading condition are given in Figure 2. The system formed is made of steel material and the torsional moments is under the influence. The diameter of the AB part of the rod is 100 mm; The diameter of the BC part is 60 mm. the shear modulus of steel is G = 80000 MPa. (a) Draw the torsional moment diagram of the rod. (b) Calculate the maximum shear stress that will develop in the system. (c) Calculate the relative rotational value of point C with respect to point A. M1(kN.m)=84 M2(kN.m)=62 L3(mm)=700 L4(mm)=500 Şekil 2 = Figure 2 a-a kesiti = a-a section b-b kesiti = b-b section
Q1/ The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying the loads shown, determine: (1) The maximum normal stress developed in each rod. (2) The horizontal displacement of end C with respect to the fixed support at A. (3) Suppose that only rod BC is exposed to change in temperature, what would be the change that keeps point C in the original position. Use Est = 200GPA, xst= 12(10)-6 600 mm 400 mm 50 kN 40 kN В C 50 kN
125. A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E = 2x105 N/mm2. The elongation of %3D the bar will be 1 (b) 6n 1 mm (a) mm (c) -mm (d) -mm 2
The assembly consists of two 20-mm diameter rods AB and CD, a 30-mm diameter rod EF, and a rigid bar G. The assembly is subjected to the loading shown, with point E located at the midpoint of BD. Take the modulus of elasticity of the rods as 100 GPa. i. Determine the horizontal displacement of point E (indicate direction, left or right). 11. If the applied loads causes the diameter of rod AB to become 20.0022 determine the Poisson's ratio of the material (to 2 decimal places). 350 mm 450 mm A B 40 kN E 60 kN 40 kN DG
The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm² Fy=345 MPa x = 164 x 106 mm4 ly = 23 x 106 mm4 Proportional limit, fs = 290 MPa The x-axis has an unbraced length of 10 m which is pinned at the top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Compute the initial compressive load of the column. Select the correct response: 6606.59 KN 3706.14 KN E = 200 GPa 1816.01 kN 926.53 kN
The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30 kN, determine the tensile forces PBE & PCF in rods BE and CF, respectively. For steel, E = 200 GPa. F 2.0 m E P = 30 kN 2.5 m D -3 m- -3 m-
Calculate the force on element BF. Establish if it is in tension or compression.