QUESTION 6 Let R1 = R2 =10 KQ. Change C1 to 159 nF and C2 to 0.793 nF. At fcLowpass. what is the predicted phase shift of the output relative to input? Hint check Lec note -57 -45 O-42.86 45 Low Pass RC filters 48 JAR -127 -15 - #7 R Berence 1 kl Vo 20 24H: (og scale) Manual frequency pose -628 difference f/fc Gain = Gain = o(j) Vija) 10% 10kx Vo(jw) Vi(jw) -3048 - -jxc R-jXc 10c 10V, leads V) 000 £10 Difference = 5.7 fo S-domain notation: s=jo, o=2nf f/fc 1 2πRC 100 g scale) Difference 57

QUESTION 6 Let R1 = R2 =10 KQ. Change C1 to 159 nF and C2 to 0.793 nF. At fcLowpass. what is the predicted phase shift of the output relative to input? Hint check Lec note -57 -45 O-42.86 45 Low Pass RC filters 48 JAR -127 -15 - #7 R Berence 1 kl Vo 20 24H: (og scale) Manual frequency pose -628 difference f/fc Gain = Gain = o(j) Vija) 10% 10kx Vo(jw) Vi(jw) -3048 - -jxc R-jXc 10c 10V, leads V) 000 £10 Difference = 5.7 fo S-domain notation: s=jo, o=2nf f/fc 1 2πRC 100 g scale) Difference 57

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The circuit in Figure 1 represents the circuit model of an interference path from source vin to the 10 MQ load resistance at vout- C1 C2 1 pF 1000 pF R V in out 10 MQ Figure 1. Interference modeling a) Determine the transfer function H(f) = vou/Vin from vin to vout- b) Determine the output magnitude vout when Vin is a 170V pk sine wave at 60HZ c) Determine the output magnitude vou when vin is a 1V pk sine wave at 1 MHz
In the circuit in the figure, Vin=30Vrms and Vout are taken from the C1 capacity. Accordingly, a) Filter find the type b) Find the cutoff frequency (fc) of the circuit c) A=Vout/Vin for f=100, 800 and fc values draw the curve?
Q4 :Find the type of this filter and cut-off frequency Wc for illustrated filter figure if L=2 mh and R=10 ohm R I Ve
For The Table 1-Find the cutoff frequency by changing the frequency until Vo becomes 0.707Vi. 2-Graph the gain and the phase against frequency.
In the circuit below, what is the closed loop gain and the width of band? What is the AC output voltage at 100 kHz? Vin 25 mVp p-p Vcc +15 V LF157A VEE -15 V R₁ 3 ΚΩ R₁ 150 Ω Vout
Please Show and Explain ALL work
The below 4 figures are the angle of the transfer function of passive filters. Phase (deg) -45- Phase (deg) (Cep) sid 45 10 10 Frequency (radisec) 10² Frequency (rad/sec) Figure-1 shows the frequency response of Figure-2 shows the frequency response of Figure-3 shows the frequency response of Figure-4 shows the frequency response of 4) ( + 4 10 10" 10
Read and solve carefully please write clearly and box the final answer Hint : Enter your answer to the 2nd nearest decimal place in percent.
beta being 100 solve for vo /vsing using smal signal model
A boost regulator has an input voltage Vs-12V and an average output voltage Va-24V. The average output load current la-1A at a switching frequency of 20 kH2. Calculate the critical value for Lc for continuous current. Select one: O a.0.15 mH O b.0.088 mH O c.0.022 mH O d. None of these
The frequency response H(en) of a linear time -in variant system is giren - in e j22 1. H (ein) = e %3D e a) Ex press the in Aut/output relatkonshie with difference equations. b) Is the system casual ? -la -M
What type of filter is shown in the Figure? Need more explanation with neat hand writing , minimum 3 steps of explanation